All Activity

This stream auto-updates     

  1. Past hour
  2. Welcome to ARMBIAN 5.87.190519 nightly Ubuntu 18.04.2 LTS 5.1.3-sunxi64 analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 1 2 3 CPUs which need to have their frequency coordinated by software: 0 1 2 3 maximum transition latency: 244 us. hardware limits: 480 MHz - 1.49 GHz available frequency steps: 480 MHz, 720 MHz, 816 MHz, 888 MHz, 1.08 GHz, 1.32 GHz, 1.49 GHz available cpufreq governors: conservative, userspace, powersave, ondemand, performance, schedutil current policy: frequency should be within 480 MHz and 1.49 GHz. The governor "ondemand" may decide which speed to use within this range. current CPU frequency is 888 MHz (asserted by call to hardware). cpufreq stats: 480 MHz:87.91%, 720 MHz:1.92%, 816 MHz:1.00%, 888 MHz:2.43%, 1.08 GHz:1.51%, 1.32 GHz:0.78%, 1.49 GHz:4.45% (26822)
  3. Right, that was why I've build the dev 5.1. It's at 1.8Ghz from boot. All frequencies are available, even 1.64Ghz) What available frequencies does it show for you? (cpufreq-info)
  4. yes sinds the last 2 nightly releases that was also my question a few posts above
  5. I am running 5.1 to. The room temperature is arround 23 degrees celcius. I have the Orange Pi One Plus H6 in a plastic case. Simple copper heatsink. Test with and without fan. Round 1 with fan Time CPU load %cpu %sys %usr %nice %io %irq CPU 18:09:44: 720MHz 0.72 3% 1% 0% 0% 1% 0% 26.9°C 18:09:49: 1080MHz 0.66 1% 0% 0% 0% 0% 0% 26.8°C 18:09:54: 1488MHz 0.69 14% 1% 9% 0% 1% 0% 29.6°C 18:10:01: 1488MHz 0.96 72% 1% 70% 0% 0% 0% 41.0°C 18:10:07: 1488MHz 1.28 89% 2% 86% 0% 0% 0% 38.9°C 18:10:14: 1488MHz 1.50 91% 2% 88% 0% 0% 0% 43.0°C 18:10:19: 1488MHz 2.04 83% 1% 81% 0% 0% 0% 39.4°C 18:10:24: 1488MHz 2.27 89% 2% 86% 0% 0% 0% 40.4°C 18:10:30: 1488MHz 2.49 97% 5% 91% 0% 0% 0% 40.9°C 18:10:35: 1488MHz 2.61 91% 1% 89% 0% 0% 0% 38.5°C 18:10:40: 1488MHz 2.73 71% 3% 67% 0% 0% 0% 40.5°C 18:10:46: 1488MHz 2.75 88% 5% 83% 0% 0% 0% 40.9°C 18:11:11: 720MHz 2.93 97% 28% 26% 0% 42% 0% 31.2°C 18:11:16: 1080MHz 12.37 5% 1% 0% 0% 2% 0% 28.8°C 18:11:21: 888MHz 11.38 2% 0% 0% 0% 0% 0% 28.8°C Round 2 with fan 18:11:26: 888MHz 10.47 4% 1% 2% 0% 0% 0% 28.4°C 18:11:31: 1080MHz 9.63 1% 0% 0% 0% 0% 0% 28.4°C 18:11:36: 888MHz 8.86 1% 0% 0% 0% 0% 0% 28.1°C 18:11:41: 1320MHz 8.15 1% 0% 0% 0% 0% 0% 28.0°C 18:11:46: 1488MHz 7.50 15% 1% 12% 0% 1% 0% 30.6°C 18:11:53: 1488MHz 7.22 83% 1% 80% 0% 0% 0% 42.5°C 18:11:58: 1488MHz 6.95 86% 1% 84% 0% 0% 0% 39.7°C 18:12:05: 1488MHz 6.71 93% 1% 91% 0% 0% 0% 43.7°C 18:12:11: 1488MHz 6.50 81% 1% 79% 0% 0% 0% 40.3°C 18:12:16: 1488MHz 6.13 89% 2% 87% 0% 0% 0% 40.7°C 18:12:21: 1488MHz 6.04 95% 2% 92% 0% 0% 0% 39.3°C 18:12:26: 1488MHz 5.88 89% 1% 88% 0% 0% 0% 36.8°C 18:12:31: 1488MHz 5.57 73% 2% 71% 0% 0% 0% 40.7°C 18:12:36: 1488MHz 5.36 86% 2% 83% 0% 0% 0% 40.6°C 18:13:31: 1320MHz 11.18 98% 47% 11% 0% 39% 0% 33.7°C Round 3 with fan Time CPU load %cpu %sys %usr %nice %io %irq CPU 18:13:36: 720MHz 28.50 3% 0% 1% 0% 1% 0% 29.6°C 18:13:42: 1488MHz 26.30 47% 1% 44% 0% 0% 0% 40.7°C 18:13:47: 1488MHz 24.51 95% 1% 93% 0% 0% 0% 44.4°C 18:13:52: 1488MHz 21.43 82% 2% 78% 0% 0% 0% 42.1°C 18:13:59: 1488MHz 20.04 94% 1% 93% 0% 0% 0% 44.8°C 18:14:04: 1488MHz 18.83 80% 2% 77% 0% 0% 0% 41.5°C 18:14:09: 1488MHz 17.88 90% 2% 87% 0% 0% 0% 41.8°C 18:14:16: 1488MHz 16.85 94% 2% 91% 0% 0% 0% 44.8°C 18:14:22: 1488MHz 15.82 78% 1% 76% 0% 0% 0% 40.6°C 18:14:27: 1488MHz 14.80 85% 2% 81% 0% 0% 0% 41.1°C 18:14:33: 1488MHz 13.06 90% 3% 87% 0% 0% 0% 41.5°C 18:14:40: 888MHz 14.57 91% 20% 37% 0% 32% 0% 31.7°C 18:14:45: 1080MHz 13.41 1% 0% 0% 0% 0% 0% 30.1°C Round 1 without fan Time CPU load %cpu %sys %usr %nice %io %irq CPU 18:18:33: 1488MHz 1.69 86% 3% 82% 0% 0% 0% 47.6°C 18:18:39: 1488MHz 1.95 95% 1% 93% 0% 0% 0% 52.2°C 18:18:44: 1488MHz 2.25 78% 2% 75% 0% 0% 0% 49.2°C 18:18:51: 1488MHz 2.47 93% 4% 87% 0% 0% 0% 50.7°C 18:18:58: 1488MHz 2.76 95% 3% 91% 0% 0% 0% 54.0°C 18:19:04: 1488MHz 2.94 77% 1% 75% 0% 0% 0% 49.9°C 18:19:09: 1488MHz 3.03 88% 6% 81% 0% 0% 0% 52.1°C 18:19:15: 1488MHz 3.18 96% 11% 84% 0% 0% 0% 52.4°C 18:19:23: 1320MHz 4.37 91% 16% 35% 0% 38% 0% 42.4°C Round 2 without fan Time CPU load %cpu %sys %usr %nice %io %irq CPU 18:20:24: 1488MHz 1.60 40% 1% 38% 0% 0% 0% 49.9°C 18:20:30: 1488MHz 2.20 94% 1% 92% 0% 0% 0% 55.8°C 18:20:35: 1488MHz 2.34 84% 2% 81% 0% 0% 0% 52.6°C 18:20:41: 1488MHz 2.48 94% 1% 93% 0% 0% 0% 57.0°C 18:20:47: 1488MHz 2.60 79% 2% 77% 0% 0% 0% 53.9°C 18:20:52: 1488MHz 2.71 90% 2% 87% 0% 0% 0% 55.2°C 18:20:58: 1488MHz 2.90 94% 2% 91% 0% 0% 0% 58.6°C 18:21:04: 1488MHz 3.06 80% 1% 78% 0% 0% 0% 54.9°C 18:21:09: 1488MHz 3.13 84% 2% 81% 0% 0% 0% 55.2°C 18:21:14: 1488MHz 3.28 89% 2% 87% 0% 0% 0% 56.1°C 18:21:24: 720MHz 4.14 93% 13% 37% 0% 41% 0% 46.4°C 18:21:30: 720MHz 4.16 1% 0% 0% 0% 0% 0% 43.6°C Round 3 without fan Time CPU load %cpu %sys %usr %nice %io %irq CPU 18:21:55: 1488MHz 2.98 42% 1% 39% 0% 0% 0% 55.1°C 18:22:01: 1488MHz 3.06 95% 2% 92% 0% 0% 0% 60.0°C 18:22:06: 1488MHz 3.30 82% 2% 79% 0% 0% 0% 56.5°C 18:22:13: 1488MHz 3.20 94% 1% 92% 0% 0% 0% 61.6°C 18:22:18: 1488MHz 3.02 80% 1% 77% 0% 0% 0% 57.3°C 18:22:23: 1488MHz 3.18 89% 2% 86% 0% 0% 0% 58.3°C 18:22:30: 1488MHz 3.40 93% 2% 90% 0% 0% 0% 62.1°C 18:22:36: 1488MHz 3.33 80% 1% 78% 0% 0% 0% 59.1°C 18:22:41: 1488MHz 3.22 85% 2% 82% 0% 0% 0% 58.8°C 18:22:47: 1488MHz 3.20 90% 2% 87% 0% 0% 0% 60.1°C 18:22:54: 1080MHz 3.59 94% 21% 44% 0% 27% 0% 50.4°C 18:22:59: 888MHz 3.70 3% 1% 0% 0% 1% 0% 46.9°C Round 4 without fan Time CPU load %cpu %sys %usr %nice %io %irq CPU 18:23:35: 1488MHz 2.54 54% 1% 52% 0% 0% 0% 57.2°C 18:23:40: 1488MHz 2.74 95% 1% 94% 0% 0% 0% 62.0°C 18:23:45: 1488MHz 2.76 81% 2% 78% 0% 0% 0% 59.0°C 18:23:52: 1488MHz 2.86 94% 1% 93% 0% 0% 0% 63.6°C 18:23:57: 1488MHz 2.79 79% 2% 77% 0% 0% 0% 59.6°C 18:24:02: 1488MHz 2.73 90% 2% 87% 0% 0% 0% 61.4°C 18:24:09: 1488MHz 2.75 94% 2% 91% 0% 0% 0% 64.0°C 18:24:15: 1488MHz 2.94 79% 1% 77% 0% 0% 0% 60.7°C 18:24:20: 1488MHz 2.94 84% 1% 82% 0% 0% 0% 61.6°C 18:24:25: 1488MHz 2.87 90% 3% 86% 0% 0% 0% 62.4°C 18:24:33: 1488MHz 3.28 94% 22% 46% 0% 24% 0% 55.4°C 18:24:38: 1080MHz 3.09 7% 1% 2% 0% 2% 0% 48.9°C
  6. Today
  7. I usually use blender. But 7zip is ok too. install it : sudo apt install p7zip-full And to run it : 7z b Run it a few times right behind each other. It doesn't max out the CPU completely. But even with that I'm getting 95°C after 2 runs. For blender you download this file and unzip. Install blender, sudo apt install blender. Open Blender and open the cpu file of the downloaded files. Then click render. I use a taskbar app to see the temperature. You can use htop or so to do the same. I also wrote a simple program to do the same. As long as you keep an eye on the temp. Do know that I'm using a dev 5.1 image. The 5.0 images should be throttling normally.
  8. 30 degrees with standard use. Not fully idle or maxed. What tool did you use for a full load test?
  9. Could you try without the fan with a full load for 15 minutes? What image do you use? The SoC can be easily cooled when using a fan. But I've got very bad results without. And what do you mean with 30 degrees? In idle or maxed out?
  10. 95 degrees celcius??? :O I got my H6 not higher than 30 degrees celsius with a simple fan and heatsink. Also when i run it before on 1.8GHz...
  11. Once it's been done nobody needs to care about it anymore. It's just a small detail, but another step closer to a more finished product. I do think the throttling is more important. I can't advice anyone to use this without proper cooling. I'm using a heatsink and it goes over 95°C. I always stopped it at that temp. I'm sure it could go well over 100°C. Certainly with CPUMiner for example. Aren't there patches for throttling that were added to 5.0 but didn't reach 5.1? I remember us trying different throttle settings. If my very bad memory serves me right it was with @TonyMac32 for the PineH64 b. But could as well have been with @martinayotte for the OPi3. I can't find the posts of that. It used to throttle at a too low temp. (I think 65/70°C) and that was changed to a higher temp. (My brain only memorize what it wants, all useless stuff that is...) Tony also later added a frequency(1.64), and this is in the 5.1 for OPi3. Here's the post of that. https://forum.armbian.com/topic/9623-pine-h64-model-b/?do=findComment&comment=76606
  12. Here is an update: I just tried replacing the kernel with 4.4.8-armada-17.02-espressobin downloaded from http://espressobin.net/tech-spec/ I put the "Image" file at "/boot/Image", and the "armada-3720-community.dtb" at "/boot/dtb/marvell/armada-3720-community.dtb". Now everything seems fine. I haven't seen any crashes at all so far, and rebooting works fine. root@espressobin:~# uname -a Linux espressobin 4.4.8-armada-17.02.2-g8148be9 #8 SMP PREEMPT Wed Jul 4 11:59:53 UTC 2018 aarch64 GNU/Linux root@espressobin:~# 7za b 7-Zip (a) [64] 16.02 : Copyright (c) 1999-2016 Igor Pavlov : 2016-05-21 p7zip Version 16.02 (locale=en_US.UTF-8,Utf16=on,HugeFiles=on,64 bits,2 CPUs LE) LE CPU Freq: 997 997 998 998 997 998 995 996 RAM size: 930 MB, # CPU hardware threads: 2 RAM usage: 441 MB, # Benchmark threads: 2 Compressing | Decompressing Dict Speed Usage R/U Rating | Speed Usage R/U Rating KiB/s % MIPS MIPS | KiB/s % MIPS MIPS 22: 868 152 555 844 | 22465 199 962 1918 23: 859 153 574 876 | 22076 199 958 1911 24: 853 153 599 918 | 21731 200 955 1908 25: 848 153 632 968 | 21340 199 953 1899 ---------------------------------- | ------------------------------ Avr: 153 590 902 | 199 957 1909 This is probably a stupid question, but why don't we just apply the patches from https://github.com/MarvellEmbeddedProcessors/linux-marvell/tree/linux-4.4.8-armada-17.02-espressobin to the 4.19.20 kernel used by Armbian? What is the current state of that work? Can I help out?
  13. I don't understand your question ... In normal Armbian builds, the uInitrd is done as a post-install script when installing Kernel Deb with DPKG.
  14. All is going normally build the image of N2 on the branch tvboxes ? I am not forming a uInitrd file. Is it a bug in my build environment or is it a common problem ?
  15. OK, I solved the problem by installing an Armbian 5.20 image I found searching for "armbian_5.20_orangepilite_debian_jessie_3.4.112.7z" on Google. However, it's not an optimal solution, because I have to be careful when updating, and Debian Jessie will no longer be supported on June 30, 2020. In order to keep it working, I have to put the following packages on hold: # apt-mark hold armbian-firmware armbian-tools-jessie linux-headers-sun8i linux-image-sun8i linux-jessie-root-orangepilite linux-u-boot-orangepilite-default sunxi-tools
  16. Actually, I have found a similar topic question in the forum. "Add: KERNELBRANCH='tag:v4.14.52' to build/userpatches/lib.config" I will give this one a go. ---------- Looks like this was a red herring. I had a look at the relevant git repo and it reports: root@ubuntu:~/build# git ls-remote -t https://github.com/rockchip-linux/kernel.git cde3c3fdf278bbf3edc895667a65c0cc16daee0c refs/tags/release-20161011 028bc40a6d227cb553236588c43f35ad7ae2af97 refs/tags/release-20161015 3e00738277533382e6a17148b80b09a8fabea268 refs/tags/release-20170220 49c16833b723b2c4fd0768483790a4f890cf2e10 refs/tags/release-20170417 3467c559d82943f7339578f92b0817b63b8b7ddc refs/tags/release-20170705 5ab215ee7f902201d4830b0b9536135143666b42 refs/tags/release-20171015 2801809213b2ebda0ab877ede0354d48fe95cde1 refs/tags/release-20171213 So the correct structure should be KERNELBRANCH='tag:release-yyyymmdd'. More on rockwell branches/tags: https://github.com/rockchip-linux/kernel
  17. Do you means "to avoid having to copy firmware files" ? I think so, but that wasn't yet a priority ...
  18. Hi All! I am having a lot of trouble making my ESPRESSObin v7 1GB DDR4 run without crashes. I have tried both Bionic (5.75 4.19.20) and Stretch (5.75 4.19.20) images, and neither are stable. I have tried with a lot of different PSUs (all switch-mode though) and booting from both microSD and USB sticks. My U-Boot is "flash-image-ddr4-1g-1cs-1000_800.bin". It seems like there is about 50% chance that it will boot without a crash. The type of crashes I get seems random. Ex TIM-1.0 WTMI-devel-18.12.0-a0a1cb8 WTMI: system early-init SVC REV: 5, CPU VDD voltage: 1.155V NOTICE: Booting Trusted Firmware NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2) NOTICE: BL1: Built : 09:50:21, Feb 20 2019 NOTICE: BL1: Booting BL2 NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2) NOTICE: BL2: Built : 09:50:23, Feb 20 2019 NOTICE: BL1: Booting BL31 NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2) NOTICE: BL31: Built : 09:5 U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100) Model: Marvell Armada 3720 Community Board ESPRESSOBin CPU 1000 [MHz] L2 800 [MHz] TClock 200 [MHz] DDR 800 [MHz] DRAM: 1 GiB Comphy chip #0: Comphy-0: USB3 5 Gbps Comphy-1: PEX0 2.5 Gbps Comphy-2: SATA0 6 Gbps SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: ncq led only pmp fbss pio slum part sxs PCIE-0: Link down MMC: sdhci@d0000: 0, sdhci@d8000: 1 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB OK Model: Marvell Armada 3720 Community Board ESPRESSOBin Net: eth0: neta@30000 [PRIME] Hit any key to stop autoboot: 0 starting USB... USB0: Register 2000104 NbrPorts 2 Starting the controller USB XHCI 1.00 USB1: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 1 for devices... 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found / ** File not found /boot.scr ** ## Executing script at 06d00000 Wrong image format for "source" command /boot/ 1119 bytes read in 26 ms (42 KiB/s) ## Executing script at 06d00000 221 bytes read in 10 ms (21.5 KiB/s) 16421376 bytes read in 803 ms (19.5 MiB/s) 4674731 bytes read in 241 ms (18.5 MiB/s) ** File not found /boot/dtb/marvell/armada-3720-community.dtb ** 8942 bytes read in 16 ms (544.9 KiB/s) ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: uInitrd Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 4674667 Bytes = 4.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 06000000 Booting using the fdt blob at 0x6000000 Loading Ramdisk to 3f1b5000, end 3f62a46b ... OK Using Device Tree in place at 0000000006000000, end 00000000060052ed Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 4.19.20-mvebu64 (root@armbian.com) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #5.75 SMP PREEMPT Fri Feb 8 09:54:18 CET 2019 [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '') [ 0.000000] bootconsole [ar3700_uart0] enabled [ 4.453025] page:ffffffbf00202d80 count:0 mapcount:0 mapping:0000000000002000 index:0x1 [ 4.458439] flags: 0x0() Loading, please wait... starting version 232 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. [ 6.143080] page:ffffffbf00ed4f40 count:8192 mapcount:0 mapping:0000000000000000 index:0x0 [ 6.148764] flags: 0x0() And then it just freezes. Or this one which includes a proper kernel Oops: Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 4.19.20-mvebu64 (root@armbian.com) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #5.75 SMP PREEMPT Fri Feb 8 09:54: 18 CET 2019 [ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Board [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '') [ 0.000000] bootconsole [ar3700_uart0] enabled [ 4.353254] page:ffffffbf00f32500 count:0 mapcount:0 mapping:0000000000002000 index:0x2 [ 4.358696] flags: 0x0() [ 4.451874] page:ffffffbf00fc6300 count:0 mapcount:0 mapping:0000000000002000 index:0x0 [ 4.457312] flags: 0x0() Loading, please wait... [ 4.500832] page:ffffffbf00fcf500 count:8192 mapcount:0 mapping:0000000000000000 index:0x0 [ 4.506499] flags: 0x0() starting version 232 [ 5.784308] page:ffffffbf00eeed40 count:0 mapcount:0 mapping:0000000000002000 index:0x0 [ 5.789746] flags: 0x0() [ 5.793003] page:ffffffbf00eeef40 count:0 mapcount:0 mapping:0000000000002000 index:0x0 [ 5.800585] flags: 0x0() [ 5.844097] page:ffffffbf00fd9800 count:0 mapcount:0 mapping:0000000000002000 index:0x1 [ 5.849538] flags: 0x0() Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. [ 6.022993] page:ffffffbf00fc6000 count:0 mapcount:0 mapping:0000000000002000 index:0x0 [ 6.028434] flags: 0x0() [ 6.031841] page:ffffffbf00ed0c80 count:0 mapcount:0 mapping:0000000000002000 index:0x0 [ 6.039272] flags: 0x0() [ 6.063514] page:ffffffbf00f3a540 count:0 mapcount:0 mapping:0000000000002000 index:0x2 [ 6.068945] flags: 0x0() [ 6.071754] page:ffffffbf00f3a500 count:0 mapcount:0 mapping:0000000000002000 index:0x2 [ 6.079784] flags: 0x0() [ 6.155043] page:ffffffbf00ed1840 count:0 mapcount:0 mapping:0000000000002000 index:0x0 [ 6.160484] flags: 0x0() Begin: Will now check root file system ... fsck from util-linux 2.29.2 [ 6.295435] Internal error: Oops: 96000005 [#1] PREEMPT SMP [ 6.298359] Modules linked in: uas mv88e6xxx dsa_core [ 6.303580] CPU: 1 PID: 25 Comm: kworker/1:1 Tainted: G B E 4.19.20-mvebu64 #5.75 [ 6.312425] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT) [ 6.319093] Workqueue: events dbs_work_handler [ 6.323630] pstate: 80000005 (Nzcv daif -PAN -UAO) [ 6.328570] pc : dev_pm_opp_set_rate+0x1b8/0x540 [ 6.333312] lr : dev_pm_opp_set_rate+0xf0/0x540 [ 6.337956] sp : ffffff8009303c10 [ 6.341363] x29: ffffff8009303c10 x28: 0000000000000000 [ 6.346828] x27: ffffffc03be3ce50 x26: 000000000ee6b280 [ 6.352293] x25: ffffffc03be3cd80 x24: ffffffc03ffb7298 [ 6.357759] x23: ffffffc03be3ce00 x22: 000000001dcd6500 [ 6.363224] x21: 0000000000000000 x20: ffffff8008f79000 [ 6.368690] x19: ffffffc03bef7e00 x18: 0000000000000007 [ 6.374155] x17: 0000000000000001 x16: 0000000000000019 [ 6.379621] x15: 0000000000000100 x14: 0000000000000400 [ 6.385086] x13: 0000000000000000 x12: 0000000000000001 [ 6.390551] x11: 0000000000000000 x10: 0000000000000910 [ 6.396017] x9 : ffffff8009303d70 x8 : 00000000005fd500 [ 6.401484] x7 : ffffffc03f255480 x6 : 0000000000000000 [ 6.406948] x5 : 0000000000000001 x4 : 0000000000000000 [ 6.412415] x3 : ffffffc03fa52700 x2 : 0000000000000000 [ 6.417878] x1 : 0000000000000000 x0 : 0000000000002000 [ 6.423351] Process kworker/1:1 (pid: 25, stack limit = 0x(____ptrval____)) [ 6.430513] Call trace: [ 6.433040] dev_pm_opp_set_rate+0x1b8/0x540 [ 6.437426] set_target+0x40/0x70 [ 6.440829] __cpufreq_driver_target+0x184/0x5b0 [ 6.445576] od_dbs_update+0xbc/0x1a0 [ 6.449341] dbs_work_handler+0x3c/0x70 [ 6.453292] process_one_work+0x1e0/0x330 [ 6.457407] worker_thread+0x40/0x460 [ 6.461170] kthread+0x128/0x130 [ 6.464487] ret_from_fork+0x10/0x1c [ 6.468165] Code: f9403fb6 54001a48 f94016fb b940d261 (f940001c) [ 6.474431] ---[ end trace 8d8b611cab491bfc ]--- [ 8.357420] Unable to handle kernel paging request at virtual address 002f343030323358 [ 8.362801] Mem abort info: [ 8.365652] ESR = 0x96000004 [ 8.368790] Exception class = DABT (current EL), IL = 32 bits [ 8.374878] SET = 0, FnV = 0 [ 8.378014] EA = 0, S1PTW = 0 [ 8.381236] Data abort info: [ 8.384170] ISV = 0, ISS = 0x00000004 [ 8.388139] CM = 0, WnR = 0 [ 8.391188] [002f343030323358] address between user and kernel address ranges [ 8.398540] Internal error: Oops: 96000004 [#2] PREEMPT SMP [ 8.404242] Modules linked in: uas mv88e6xxx dsa_core [ 8.409457] CPU: 1 PID: 175 Comm: d0032004.mdio-m Tainted: G B D E 4.19.20-mvebu64 #5.75 [ 8.418757] Hardware name: Globalscale Marvell ESPRESSOBin Board (DT) [ 8.425396] pstate: 80000005 (Nzcv daif -PAN -UAO) [ 8.430344] pc : mutex_lock+0x14/0x40 [ 8.434156] lr : mv88e6xxx_adjust_link+0x3c/0xa0 [mv88e6xxx] [ 8.439900] sp : ffffff8009afbc50 [ 8.443306] x29: ffffff8009afbc50 x28: 0000000000000000 [ 8.448771] x27: ffffff8009077a48 x26: ffffff8008f79000 [ 8.454237] x25: ffffffc03ba49008 x24: ffffff8009077000 [ 8.459703] x23: 732f343030323340 x22: 732f343030323358 [ 8.465167] x21: 0000000000000013 x20: ffffffc03f31d000 [ 8.470633] x19: ffffffc03f31d000 x18: ffffffc03c3a1090 [ 8.476099] x17: 0000000000000001 x16: 0000000000000019 [ 8.481565] x15: 0000000000000100 x14: 0000000000000400 [ 8.487030] x13: 0000000000000000 x12: 0000000000000001 [ 8.492495] x11: 0000000000012adb x10: 0000000000000040 [ 8.497961] x9 : ffffff8008f92d70 x8 : ffffffc03cc00248 [ 8.503426] x7 : ffffffc03cc00430 x6 : 00000000000001c0 [ 8.508892] x5 : 000000403706c000 x4 : 0000000000000000 [ 8.514358] x3 : ffffff8000bb61a0 x2 : ffffffc03be8c100 [ 8.519824] x1 : 0000000000000000 x0 : 732f343030323358 [ 8.525295] Process d0032004.mdio-m (pid: 175, stack limit = 0x(____ptrval____)) [ 8.532904] Call trace: [ 8.535435] mutex_lock+0x14/0x40 [ 8.538881] mv88e6xxx_adjust_link+0x3c/0xa0 [mv88e6xxx] [ 8.544302] mdiobus_read+0x48/0x70 [ 8.547881] m88e1121_did_interrupt+0x1c/0x30 [ 8.552364] phy_change+0x2c/0x108 [ 8.555857] phy_interrupt+0x1c/0x30 [ 8.559536] handle_nested_irq+0xb0/0x130 [ 8.563705] mv88e6xxx_g2_irq_thread_fn+0x98/0xd0 [mv88e6xxx] [ 8.569567] handle_nested_irq+0xb0/0x130 [ 8.573732] mv88e6xxx_g1_irq_thread_work+0x9c/0xd8 [mv88e6xxx] [ 8.579823] mv88e6xxx_irq_poll+0x18/0x38 [mv88e6xxx] [ 8.584978] kthread_worker_fn+0xac/0x198 [ 8.589096] kthread+0x128/0x130 [ 8.592414] ret_from_fork+0x10/0x1c [ 8.596091] Code: d2800001 d5384102 910003fd f9800011 (c85ffc03) [ 8.602354] ---[ end trace 8d8b611cab491bfd ]--- While running, I get errors like this one: [ 71.136812] BUG: Bad page state in process khugepaged pfn:31d99 [ 71.140206] page:ffffffbf00c76640 count:0 mapcount:0 mapping:0000000000002000 index:0x0 [ 71.148428] flags: 0x0() [ 71.151049] raw: 0000000000000000 0000000000000000 ffffffbf00c76648 0000000000002000 [ 71.159015] raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 [ 71.166975] page dumped because: non-NULL mapping [ 71.172329] BUG: Bad page state in process khugepaged pfn:3261c [ 71.178001] page:ffffffbf00c98700 count:0 mapcount:0 mapping:0000000000002000 index:0x0 [ 71.186236] flags: 0x0() [ 71.188853] raw: 0000000000000000 0000000000000000 ffffffbf00c98708 0000000000002000 [ 71.196825] raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 [ 71.204782] page dumped because: non-NULL mapping Once successfully booted, setting the CPUfreq governor to "performance" seems to make it more stable. Am I the only one having problems getting a stable boot on V7? Has anyone of you any tips on how to make it stable? I am willing to try compiling a new kernel if some experimental patches exists.
  19. I've booted from SD, bring a copy of the image via SSH/SCP, then "dd if=Armbian_5.86_Odroid-n2_Debian_buster_default_5.1.0_20190514.img of=/dev/mmcblk0 bs=100M" ...
  20. actual - where jessie has been archived - you should start with the following /etc/apt/sources.list: deb http://archive.debian.org/debian/ jessie main contrib non-free deb-src http://archive.debian.org/debian/ jessie main contrib non-free deb http://security.debian.org jessie/updates main contrib non-free deb-src http://security.debian.org jessie/updates main contrib non-free and enter the following commands: sudo apt-get update sudo apt-get upgrade sudo apt-get dist-upgrade then change the content of /etc/apt/sources.list to: deb http://httpredir.debian.org/debian stretch main contrib non-free deb http://httpredir.debian.org/debian stretch-updates main contrib non-free deb http://httpredir.debian.org/debian stretch-backports main contrib non-free deb http://security.debian.org/ stretch/updates main contrib non-free then redo: sudo apt-get update sudo apt-get upgrade sudo apt-get dist-upgrade and after that for cleanup: sudo apt-get autoremove sudo apt-get autoclean You have to check that there is no other sources-list or another package-list in the directory /etc/apt/sources.list.d
  21. Hi Igor How about including "webseeds"/"http seeds" in your .torrent files? You already have a lot of mirrors (ex http://mirrors.dotsrc.org/armbian-dl/), so it would be very helpful if your torrent client could also download from all those mirrors. Spec: http://www.bittorrent.org/beps/bep_0019.html
  22. What headers do you compile when you upgrade ? Now Disko does not work LIGHTDM, so I do not build these versions. After the packages are fixed, I will continue to build them.
  23. Actually, I have found a similar topic question in the forum. "Add: KERNELBRANCH='tag:v4.14.52' to build/userpatches/lib.config" I will give this one a go.
  24. I downloaded the kernel source and kernel headers on a rk3288 rockchip (tinkerboardS) and noticed there was a mismatch between kernel version, armbian release and chipset (rockchip64) - see below. root@tinkerboard:~# uname -a Linux tinkerboard 4.4.174-rockchip #7 SMP Sun Feb 10 11:57:26 CET 2019 armv7l armv7l armv7l GNU/Linux root@tinkerboard:~# cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=tinkerboard BOARD_NAME="Tinkerboard" BOARDFAMILY=rockchip VERSION=5.75 LINUXFAMILY=rockchip BRANCH=default ARCH=arm IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMAGE_TYPE=zImage root@tinkerboard:/usr/src# ls * linux-rockchip64-default_4.4.178_5.85_config.xz linux-source-4.4.178-rockchip64.tar.xz
  25. I will check this option at myself and I will write result. How do you install the system in eMMC (what commands do you use) ?
  26. You can't have both at the same time. Not on Armbian and not on any other system unless you enforce virtualization, adjust ports of many shared services ...
  1. Load more activity