Jump to content

CSC Armbian for RK322x TV box boards

jock

By jock
in Rockchip CPU Boxes

 Share

Recommended Posts

Maker39

Maker39

Posted
Posted
  On 12/11/2022 at 9:27 AM, jock said:

I suggest to you to run armbian on sdcard and do some tests with rk322x-config.

You need to try the various combinations from the eMMC section

Expand  

* don't set any options
https://paste.armbian.com/nuquzizino
* emmc-pins alone
https://paste.armbian.com/ravorodada
* emmc-pins + emmc-ddr-ph45
https://paste.armbian.com/didajaqeko
* emmc-pins + emmc-ddr-ph180
https://paste.armbian.com/yiqutaxaqi
* emmc-pins + emmc-hs200
only "Install/update bootloader on SD/eMMC" option available

0
Maker39

Maker39

Posted
Posted
  On 12/12/2022 at 8:49 PM, jock said:

is the emmc working with pins + ddr-ph45 overlay?

Expand  

No

dmesg after armbian-install

[  103.467966] mmc_host mmc2: Bus speed (slot 0) = 2343750Hz (slot req 400000Hz, actual 390625HZ div = 3)
[  103.528295] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
[  103.532463] blk_update_request: I/O error, dev mmcblk2, sector 0 op 0x1:(WRITE) flags 0x800 phys_seg 1 prio class 0
[  103.532582] Buffer I/O error on dev mmcblk2, logical block 0, lost async page write

 

dmesg after armbian config/... boot from eMMC-system on eMMC

[   81.469807] mmc_host mmc2: Bus speed (slot 0) = 2343750Hz (slot req 400000Hz, actual 390625HZ div = 3)
[   81.530225] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
[   81.534394] blk_update_request: I/O error, dev mmcblk2, sector 0 op 0x1:(WRITE) flags 0x800 phys_seg 1 prio class 0
[   81.534484] Buffer I/O error on dev mmcblk2, logical block 0, lost async page write
[   81.842872] blk_update_request: I/O error, dev mmcblk2, sector 0 op 0x1:(WRITE) flags 0x800 phys_seg 3 prio class 0
[   81.842943] Buffer I/O error on dev mmcblk2, logical block 0, lost async page write
[   81.843012] Buffer I/O error on dev mmcblk2, logical block 1, lost async page write
[   81.843031] Buffer I/O error on dev mmcblk2, logical block 2, lost async page write
[   81.843230] blk_update_request: I/O error, dev mmcblk2, sector 15269864 op 0x1:(WRITE) flags 0x800 phys_seg 3 prio class 0
[   81.843250] Buffer I/O error on dev mmcblk2, logical block 1908733, lost async page write
[   81.843278] Buffer I/O error on dev mmcblk2, logical block 1908734, lost async page write
[   81.843293] Buffer I/O error on dev mmcblk2, logical block 1908735, lost async page write
[   81.858078] blk_update_request: I/O error, dev mmcblk2, sector 0 op 0x1:(WRITE) flags 0x800 phys_seg 1 prio class 0
[   81.858149] Buffer I/O error on dev mmcblk2, logical block 0,

0
drigohighlander

drigohighlander

Posted
Posted

Hi guys, sorry my bad english in advanced

I bought an MXQ PRO 5k and this have the rockchip 322x.

Multitool boots fine, but, sometimes it doesn't detect the internal ROM

saying something "no emmc device found" something like that, so I reboot and it works

But I can't do anything, I had trying to do the Backup first and it got stuck in 0% for hous...

BTW I don't know why this multitool image doesn't have the step-nand option..but anyway

Acessing the bash shell, the output of dmesg command show errors either in mmcblk1 (my sdcard)

and mmcblk2 (the internal rom)

My sdcard is new, and is everything ok with it, I have two bought together with the tv box weeks before this post

Burn the image several times..

Maybe my tvbox came broken? It's start android normally...

Somebody have any idea?

Thanks in advance.

0
MattWestB

MattWestB

Posted
Posted

@drigohighlander I think you have the same box i is having. For 11 months multitool was not working at all with it and not possible connecting to it and using multitool from CLI but it shall being fixed with the updated version.

The large problem is that HDMI was /is not working on it.

Your device dont have is having eMMC and then you is not getting options for step-nand option.

I was erasing the eMMC and flashing one bootloader in it and booted armbian from SD-Card and it was working OK also from USB flash. Then working OK i was installing armbian from armbian-config on the eMMC and its working very good.

Only thing i have not getting working is WiFi / Bt but i only using Ethernet so its OK for my and HDMI is also not braking thing for my then using SSH and docker / Portainer for doing the needed things on it.

0
jock

jock

Posted
  • Author
Posted

@drigohighlander please post your dmesg log, photos of the board, the original dtb or a link to the original firmware.

If you don't post informations about your hardware but just say "does not work" we can't help at all.

0
jock

jock

Posted
  • Author
Posted

@drigohighlander you posted no useful information there: the dmesg link is broken and the dtb file comes from the multitool. I asked for the original device tree.

I still see no photos of the board.

0
mwe

mwe

Posted
Posted (edited)

Hi,

 

I have installed the image (Linux v88 4.4.194-rk322x #2 SMP Wed Aug 25 20:09:42 UTC 2021) to the nand of my V88 4k and it works.

  

Chip type: RK3229 - Serial: URKN50020 0000000013212d                   x
CPU Leakage: 0x06 - Logic Leakage: 0x05                                x
Internal flash: NAND                                                   x
Wifi device: South Silicon Valley 6051p/6256p - Device ID: 3030:3030 

 

I setup Wifi and it works but only if i connect the ethernet cabel(!?)

if i boot without the cabel, no wifi... I plugin the cabel, both IPs reachable 

 

Any idea 💡?

 

Best regards 

Markus

Edited by mwe
typo
0
jock

jock

Posted
  • Author
Posted

@mwe Perhaps you're trying to ping the wifi interface from another machine? Because the ssv6051 suffered a problem with the broadcast ARP packets that has been solved in the mainline flavour of the kernel, which does not work with NAND yet.

In practice the driver does not respond to ARP packets, so the wifi interface does not "announce" itself to others when asked to. The presence of the ethernet may cause some side effects that let the interface announce deliberately and so it works.

1
MR01

MR01

Posted
Posted (edited)

@jocki installed, one year ago, 5.15.35 image on internal storage.

Im not sure where im wrong, but i cant boot into sdcard multi tool (i want to make a backup of internal storage so i can restore before doint testing and junking the system)

 

Is possible or in old 5.15.35 the u-boot only boot internal storage?

Edited by MR01
0
jock

jock

Posted
  • Author
Posted

@MR01 It should work as usual, that part never changed and the boot priority is always sdcard -> USB -> eMMC. I don't remember if there were minor or major bugs in that part in the past. Perhaps you can try to upgrade the bootloader with apt update && apt install linux-u-boot-rk322x-box-current, but usually it is best to upgrade bootloader and kernel together, so I don't suggest to do that.

 

You can also try to boot multitool from USB stick, but the best way to do experiments is to burn an armbian image onto sdcard or USB stick so you don't touch the installed system. Of course remember to decompress the image first, if your image writer does not so automatically.

1
Arden King

Arden King

Posted
Posted

Thanks to all for the hard work 

I needed  an SBC for a Magic Mirror project manged to resurrect an old TV box for the job so saved money and prevented something potentially going to landfill 

 

Mine was is branded   "Mini Q1"  only issue is no Wi-Fi isn't working  rkconfig reports the it as 02e7:9086 and unknown so using a USB stick for wifi atm 

is there a fix for this 

 

Other question as I'm in need of another cheap sbc is there one that is known to be fully supported  ?

 

Thanks 

 

Arden 

0
RaptorSDS

RaptorSDS

Posted
Posted
  On 1/1/2023 at 11:01 PM, Arden King said:

rkconfig reports the it as 02e7:9086 and unknown

Expand  

 

thats a clone of realtek with name S9012P , i had also a box with a similar clone . Its close source and the Manufacture has no real linux driver

 

 

 

my solution was reflow/resolder a realtek RTL8723 DS/BS from ali... 

 

its pin and pin behavior compatible , but without a proper driver the AP S9012P is useless in linux

1
speed21

speed21

Posted
Posted

 

My board decided to crap its pants after flashing armbian for the 10th time but I managed to revive it.

 

Not sure if this is useful but I found the clock pin that I can connect GND to make the box enter MASKROM mode my board has an emcp chip on it

My model is MXQPRO_V71

you can solder a wire to this point and short it to ground then plug in your sdcard with multitool

short the clock pin to the ground and plug the power, wait till the led indicator turns red then remove the jumpers. if the led starts flashing then you are all set! you can try flashing armbian or your stock firmware to your box

324519427_6155918971109400_4934968235533545044_n.jpg

2
tommyboy

tommyboy

Posted
Posted

Hello, I bought this TV box and burned the Multitool on an SD card, after I put the SD card, it works fine for about 1 minute and then stop. The log from the Uart show

 

The end of the log :    "[    9.269594] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck."

 

https://ibb.co/g7s4Lp6
https://ibb.co/HK4cYC8
https://ibb.co/jTkc2v6
https://ibb.co/HYBqKHw

 

  Reveal hidden contents


 

 

 

 

0
jock

jock

Posted
  • Author
Posted

@tommyboy You did not specify if armbian stops working or the multitool. I guess you're talking about the multitool, since you posted the dmesg of that one.

Try to substitute rk322x-box.dtb in the multitool partition with this one: rk322x-box.dtb and try again

0
tommyboy

tommyboy

Posted
Posted

Hello i replaced rk322x-box.dtb  and tried again, result is different but again multitool stop.

End of log file:

 

Debian GNU/Linux 10 multitool ttyS2

multitool login: root (automatic login)

sh: 1: cannot create /run/motd.dynamic.new: Read-only file system

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
-bash: cannot set terminal process group (-1): Inappropriate ioctl for device
-bash: no job control in this shell
root@multitool:~# [    6.877807] FAT-fs (mmcblk0p1): Volume was not properly unm ounted. Some data may be corrupt. Please run fsck.
[    7.819053] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data  may be corrupt. Please run fsck.

tv-box-log.txtFetching info...

0
jock

jock

Posted
  • Author
Posted

@tommyboy what do you mean with "multitool stops"? You are supposed to interact with it with a monitor attached to the board HDMI port or via SSH, not using the serial adapter port that is just for debugging. The log looks pretty fine to me, you should be able to use the multitool.

0

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines

  I accept