Jump to content

No network after upgrade to 5.30

nihilista

By nihilista
in Allwinner sunxi

 Share

Recommended Posts

nihilista

nihilista

Posted
Posted

Updated my bananapi pro to from 5.30 minutes ago...but now it doesnt boot ;-(

Any possibility to get my system back without setting up completely new? Never had this with all update before.....

nihilista

nihilista

Posted
  • Author
Posted

Seems to be problem with network (using it headless), last line bootscreen says IPv6 ADDRCONF (NETDEV_CHANGE)  : eth0: link becomes ready. In line before it states link is up, ipscan shows no bananapro...

Igor

Igor

Posted
Posted
49 minutes ago, nihilista said:

Updated my bananapi pro to from 5.30 minutes ago...but now it doesnt boot ;-(

Any possibility to get my system back without setting up completely new? Never had this with all update before.....


Everything is solvable ... but we need more information to help. It might be a problem with u-boot. From where you did upgrade?

1
Igor

Igor

Posted
Posted
25 minutes ago, tahaea1 said:

Same problem on SuperPi. Can get console with UART but get no networking at all.


Which image?

Igor

Igor

Posted
Posted
4 minutes ago, tahaea1 said:

Banana Pi Jessie mainline

upgraded with apt-get

using usb hdd as root


Which kernel version and from which Armbian version you made update? Did you start from clean image? You have to tell me everything! btw. Super Pi is not supported even I am almost sure it's exactly the same as Banana Pi ... I never saw one of those ... some minor changes can lead to improper Ethernet initialisation. I also need to wait for others to report - on supported boards.

tahaea1

tahaea1

Posted
Posted
7 minutes ago, Igor said:


Which kernel version and from which Armbian version you made update? Did you start from clean image? You have to tell me everything! btw. Super Pi is not supported even I am almost sure it's exactly the same as Banana Pi ... I never saw one of those ... some minor changes can lead to improper Ethernet initialisation. I also need to wait for others to report - on supported boards.

I don't really remember the kernel version. Armbian version was 5.25 or 5.24. Clean image as in what? I was using 5.25 for about 2 months I think? was apt updating regularly and it updated to 5.30 today. 

Igor

Igor

Posted
Posted
3 minutes ago, tahaea1 said:

I don't really remember the kernel version. Armbian version was 5.25 or 5.24. Clean image as in what? I was using 5.25 for about 2 months I think? was apt updating regularly and it updated to 5.30 today. 


OK. I'll try to reproduce.

 

In the mean time, you can try to flash (downgrade) u-boot from http://apt.armbian.com/pool/main/l/linux-u-boot-bananapi-default/linux-u-boot-bananapi_5.25_armhf.deb to see if that helps. Extract  u-boot-sunxi-with-spl.bin and write to SD card: 

dd if=u-boot-sunxi-with-spl.bin of=/dev/yoursdcard bs=1024 seek=8 status=noxfer

 

nihilista

nihilista

Posted
  • Author
Posted

Using latest 5.25, jessie,  with 4.9.7 mainline kernel here. Will try downgrade u-boot if i found time and got running linux machine ;-)

wsian

wsian

Posted
Posted

Bananapi armbian 5.27 mainline upgrade to 5.30. Cannot log in remotely from putty.. When connect to hdmi monitor, it boot up normally and can log in. Everything seems ok but no response when attempt to log in remotely (putty). Very strange.

Igor

Igor

Posted
Posted
5 minutes ago, wsian said:

Bananapi armbian 5.27 mainline upgrade to 5.30. Cannot log in remotely from putty.. When connect to hdmi monitor, it boot up normally and can log in. Everything seems ok but no response when attempt to og in remotely (putty). Very strange.


Most likely u-boot configuration which initialised network is broken for Bananapi. Still checking if this is it. U-boot upgrade has been removed until this is not resolved.

Igor

Igor

Posted
Posted

Bananapi M1+

Upgrade from 5.24 / 4.7.9 -> 5.30 / 4.11.4: no problems with network. Tested with 100 / 1000Mbit switch.

Igor

Igor

Posted
Posted

The more I test, the less I know :( This test image works fine on M1+, while network doesn't come up (properly) on: M1, PRO and R1 :)

1
Igor

Igor

Posted
Posted
15 minutes ago, Wolf2000 said:

Hi Igor
With my Banana Pi 1 nothing more about HDMI I see only the cursor flashes.
What could I do?
Or is it death?


Even you wait until network timeouts ? 

If you did an update, you need to rollback u-boot to 5.25 

Guest

Guest

Posted
Posted

I can confirm, on a BPi M1 the internal ethernet is broken with armbian 5.30.

I'm using the BPi M1 as bridge with a second USB ethernet port. After update to armbian 5.30 (from 5.26), the internal BPi ethernet port had 80% packet loss, but the USB ethernet adapter works just fine.

 

Regards

 

Charizard

Charizard

Posted
Posted

Hello,

 

I have been just installed Armbian 5.30 ubuntu flavor on my Banana Pi (the first model). Unfortunately, it's impossible to start a SSH session. The session freeze before to get the prompt. 

 

Quote

64 bytes from 192.168.1.37: icmp_seq=1 ttl=64 time=0.487 ms
64 bytes from 192.168.1.37: icmp_seq=4 ttl=64 time=0.267 ms
64 bytes from 192.168.1.37: icmp_seq=6 ttl=64 time=0.287 ms
64 bytes from 192.168.1.37: icmp_seq=7 ttl=64 time=0.271 ms
64 bytes from 192.168.1.37: icmp_seq=8 ttl=64 time=0.334 ms
From 192.168.1.57 icmp_seq=10 Destination Host Unreachable
64 bytes from 192.168.1.37: icmp_seq=13 ttl=64 time=1028 ms
64 bytes from 192.168.1.37: icmp_seq=15 ttl=64 time=0.246 ms
64 bytes from 192.168.1.37: icmp_seq=22 ttl=64 time=0.318 ms
64 bytes from 192.168.1.37: icmp_seq=74 ttl=64 time=0.297 ms
64 bytes from 192.168.1.37: icmp_seq=76 ttl=64 time=0.308 ms

 

304 packets transmitted, 85 received, +5 errors, 72% packet loss, time 310268ms
rtt min/avg/max/mdev = 0.208/24.450/1028.213/155.519 ms, pipe 11

 

As you can see, a lot of packets are lost. 

 

On my Nanopi, I got other network issues with this kernel. I think the 4.11 kernel cannot be used correctly with these boards now.

Echo

Echo

Posted
Posted

Is the problem related to the BananaPi (family) only? I've just upgraded my OrangePi PC, but didn't reboot yet.

Igor

Igor

Posted
Posted
9 minutes ago, Echo said:

I've just upgraded my OrangePi PC, but didn't reboot yet.


This problem should not be related ... if you report the problem, we need all possible details :)

Aux

Aux

Posted
Posted

Hi, its a my first post here :-)

 

same issue with update from Armbian 5.25 to 5.30 bootloop on Banana Pi.

Have now done backup back, Will now wait until the problem is solved...

Echo

Echo

Posted
Posted
37 minutes ago, Igor said:


This problem should not be related ... if you report the problem, we need all possible details :)

OrangePi PC update was successfully. A reboot succeeded. Thanks for the update!

Igor

Igor

Posted
Posted
59 minutes ago, zador.blood.stained said:

Please try testing after recompiling the u-boot now.

 

M1 and PRO are O.K., will check R1 and M1+ too

 

4 minutes ago, Aux said:

same issue with update from Armbian 5.25 to 5.30 bootloop on Banana Pi.


Using u-boot from previous version is a way to go - you have to update it on another computer if you already issued an update.

 

1 minute ago, Echo said:

OrangePi PC update was successfully. A reboot succeeded. Thanks for the update!

 

You are welcome.

Aux

Aux

Posted
Posted
2 minutes ago, Igor said:

Using u-boot from previous version is a way to go - you have to update it on another computer if you already issued an update.

I tried  

Quote 

dd if=u-boot-sunxi-with-spl.bin of=/dev/yoursdcard bs=1024 seek=8 status=noxfer

but had not worked,  Had possibly flashed wrong drive mmcblk0p1 instead of mmcblk0  ??

Guest
This topic is now closed to further replies.
 Share
Go to topic listing
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines

  I accept