11 11
vlna

H2: Sunvell R69 Android TV Box (AliExpress)

Recommended Posts

5.5 rc2

@guidol  thank you for rom

@nylonatathep  thank you for fix usb

I try flash to emmc . flash time 3 minutes
emmc flash finish but don't boot

Share this post


Link to post
Share on other sites
On 12/29/2019 at 3:16 AM, 062621AM said:

I hope you're not asking how to troubleshoot Android issues.

Hi,

 

I do not know if this is an Android issue or something else. I just want to know if there is someone here who knows how to change mac adress on a R69 tv-box because my boxes has the same and wrong mac adress. I need to change it permanently to their right mac adress and do not know how or if it is possible? I bought them like this from the net and I can not understand how they can have the same mac adress.

Share this post


Link to post
Share on other sites
On 1/13/2020 at 7:24 PM, Manolo3 said:

Android issue

If you want to install some Android that maybe don't mess with MAC address maybe in https://h3droid.com/ you can find the solution. 

This is a special version of Android optimized for the SoC H2+ (normally found in the Sunvell R69) and also for H3. 

Share this post


Link to post
Share on other sites

i have a mxq pro 4k with a h3 processor

I am not able to boot to any image till now

its 8gb Rom and 2gb  Ram. 

 

i think the big problem is Nand(not emmc) storage.

here are the board pictures

20200212_155734.jpg

20200212_155709.jpg

20200212_155729.jpg

Share this post


Link to post
Share on other sites
(edited)

@guidol did you have any new images ready for sunvell r69 with kernel 5.x and proper analog-audio dts?

Edited by Ernest Kusa

Share this post


Link to post
Share on other sites
(edited)

OK, I compiled new image for Sunvell R69

 

Armbian_20.05.0-trunk_Sunvell-r69_buster_current_5.4.33_minimal

- Installation/flashing to internal emmc via armbian-config works fine

- 2 x USB works
- Analog audio device is detected but I can't get any sound, maybe my unit is broken or I'm doing something wrong (feedback needed)

- Working IR, WiFi and ethernet
- Default password (root/1234)

 

https://mega.nz/file/4ugAhKjb#NIt6KIv2tsPFzVVGwLcykFSdQp0MgCXgdCzxcj0PUxA

Edited by Ernest Kusa

Share this post


Link to post
Share on other sites
3 hours ago, Ernest Kusa said:

OK, I compiled new image for Sunvell R69

Armbian_20.05.0-trunk_Sunvell-r69_buster_current_5.4.33_minimal

- Analog audio device is detected but I can't get any sound, maybe my unit is broken or I'm doing something wrong
(feedback needed)

@Ernest Kusa Thanks for compiling ;) Did you use some special options in the armbian-build-system or just stadard?

Analog-Audio and HDMI sound is working on my Sunvell R69 with red pcb (1GB Ram).
Analog-Audio is only set to a very low volume.

Do a 
apt install alsa-utils mpg123
and use
alsamixer
to set Line-Out and DAC to a value around 75 (upper limit of the white range)

 

I could play internetradio just fine ;)
 

Analog-Audio:
mpg123 -v -b 1024 -a hw:0,0 -@ ./MP3_FFH80s

HDMI:
mpg123 -v -b 1024 -a hw:1,0 -@ ./MP3_FFH80s

aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 [CDC PCM Codec-0]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 1: allwinnerhdmi [allwinner-hdmi], device 0: 1c22800.i2s-i2s-hifi i2s-hifi-0 [1c22800.i2s-i2s-hifi i2s-hifi-0]
  Subdevices: 1/1
  Subdevice #0: subdevice #0

Welcome to Armbian buster with Linux 5.4.33-sunxi

No end-user support: built from trunk

package bsp-kernel[20.05.0-trunk] u-boot[20.05.0-trunk] dtb   [20.05.0-trunk]
firmware          [20.05.0-trunk] config[] branch[current]

 

MP3_FFH80s

Share this post


Link to post
Share on other sites

@Ernest Kusa seeing your compile did work so well I was a little bit more "brave" and compiled the dev version
Armbian bullseye with Linux 5.6.5-sunxi ;)  (non-minimal = console only image)

 

Also here no more problems - on my site - with ethernet going down/up.

Audio is working like on your current compiled image :)

I didnt check emmc, because I want to have there the android inside.

 

Welcome to Armbian bullseye with Linux 5.6.5-sunxi

No end-user support: built from trunk & unsupported (bullseye) userspace!

package bsp-kernel[20.05.0-trunk.111] u-boot[20.05.0-trunk] dtb   [20.05.0-trunk.111]
firmware          [20.05.0-trunk]     config[20.05.0-trunk] branch[dev]

System diagnosis information will now be uploaded to http://ix.io/2iOj

Share this post


Link to post
Share on other sites
(edited)
On 4/20/2020 at 12:29 PM, guidol said:

Do a 
apt install alsa-utils mpg123
and use
alsamixer
to set Line-Out and DAC to a value around 75 (upper limit of the white range)

 

 

Thanks for the advice. The sound works but very quietly. I set up the changes in alsamixer and save them but it is still barely audible. Despite this I am happy because system is stable (Im using this box as octoprint server)

Cheep USB sound card works fine tho

Edited by Ernest Kusa

Share this post


Link to post
Share on other sites
On 4/20/2020 at 11:25 AM, Ernest Kusa said:

OK, I compiled new image for Sunvell R69

 

Armbian_20.05.0-trunk_Sunvell-r69_buster_current_5.4.33_minimal

- Installation/flashing to internal emmc via armbian-config works fine

- 2 x USB works
- Analog audio device is detected but I can't get any sound, maybe my unit is broken or I'm doing something wrong (feedback needed)

- Working IR, WiFi and ethernet
- Default password (root/1234)

 

https://mega.nz/file/4ugAhKjb#NIt6KIv2tsPFzVVGwLcykFSdQp0MgCXgdCzxcj0PUxA

Great job! :thumbup:

Thanks to you I finally have a working image for my MXq-4k , :beer:

PCB silkscreen : MXQ-S-V3.0-20180126 ZN

Hw: Allwinner H3, 1G DDR3, 8G NAND, XR819

XR819 work

All 4 USB enable from armbian-config

cpufreq is working.

Because i have NAND system transfer to eMMC does not work ...

 

 

IMG_TOP.jpg

IMG_BOTTOM.jpg

IMG_NAND.jpg

IMG_RAM.jpg

IMG_MARK.jpg

Share this post


Link to post
Share on other sites

What about the transfer of Armbian from SD to NAND?

Is it possible?

Is it worth it?

Or is it worth removing NAND and soldering eMMC?

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
11 11