39 39
constantius

Orangepi 3 h6 allwiner chip

Recommended Posts

Hi, I'm new to orangepi3

I tried to run Armbian from SD card. I logged to a system, but couldn't start the GUI.

Can anyone help ?

 

Thanks

Share this post


Link to post
Share on other sites

Wow! awesome work guys! 

 

my external USB3 drive bandwidth is completely saturated with the Gigabit ethernet around my house!

really fast board too!

 

thanks so much!

Share this post


Link to post
Share on other sites
5 hours ago, data said:

Is the automatic nightly built for the lite2 still paused?

They have been re-enabled, but ...

@Igor build servers don't seems to do those recent nightly builds !

Share this post


Link to post
Share on other sites
(edited)

Hello, I have a problem on Orange Pi 3 with armbian ubuntu 5.83.190426, 5.84.190508

 

When replug ethernet cable (or reboot router), network speed becomes slow (~64KB/s per connection or something like this) :(

`reboot` helps

`nmcli device disconnect eth0 && nmcli device connect eth0` not helps

 

When unplug, lights go on (yellow constant, green flashing) 

When power on (boot) without cable plugged, lights off, when plug, lights on, speed fine

 

Maybe system do not detect correctly ethernet unplug :huh:

 

What can I do with this problem?

If full fix not easy, is it possible to reboot only ethernet to fix it, without system reboot?

UPDATE: `sudo ip link set eth0 down && sudo ip link set eth0 up` helps to fix without reboot (I thought I tried it before)

 

Feel free to ask more info if needed

Edited by Vany
partial solution found

Share this post


Link to post
Share on other sites

I've just tried "Armbian_5.84.190508_Orangepi3_Ubuntu_bionic_dev_5.1.0"

There seems to be no throttling happening. I've let it go to 96°C with heatsink and no throttling occured. Don't want to go any higher :D
I've tried with different governors, all the same.

 

Otherwise it seems good. Still needs the wifi fix, and still no sound.

Share this post


Link to post
Share on other sites
On 5/9/2019 at 3:01 PM, HannesH said:

Would really really appreciate if next version would include that too


Here is written what you need to do to make this happen.

Share this post


Link to post
Share on other sites
On 5/10/2019 at 3:57 PM, martinayotte said:

build servers don't seems to do those recent nightly builds !


Back online. They were made a few hours ago.

Share this post


Link to post
Share on other sites

1. How to update opi3 with new builds? apt dist-upgrade?

2. How to turn off red light on op3 board?

Share this post


Link to post
Share on other sites
9 hours ago, AZ8 said:

1. How to update opi3 with new builds? apt dist-upgrade?

2. How to turn off red light on op3 board?

1. Not sure if even necessary but check armbian-config to switch to nightly builds. Be aware that this can brick your board at any time.

2. I do not have an OPi3, though an OnePlus which is also shipped with H6 SoC. Try this:

 

#!/bin/bash
echo "heartbeat" > /sys/devices/platform/leds/leds/orangepi:red:pwr/trigger
sleep 2
echo "none" > /sys/devices/platform/leds/leds/orangepi:red:pwr/trigger

For unknown reason the board does not accept if I write none directly into the trigger, so I wrote this small script.

Share this post


Link to post
Share on other sites
3 hours ago, Werner said:

1. Not sure if even necessary but check armbian-config to switch to nightly builds. Be aware that this can brick your board at any time.

2. I do not have an OPi3, though an OnePlus which is also shipped with H6 SoC. Try this:

 


#!/bin/bash
echo "heartbeat" > /sys/devices/platform/leds/leds/orangepi:red:pwr/trigger
sleep 2
echo "none" > /sys/devices/platform/leds/leds/orangepi:red:pwr/trigger

For unknown reason the board does not accept if I write none directly into the trigger, so I wrote this small script.

/sys/devices/platform/leds/leds/orangepi:red:pwr/trigger: No such file or directory
 

Share this post


Link to post
Share on other sites
3 hours ago, SchmuseTigger said:

/sys/devices/platform/leds/leds/orangepi:red:pwr/trigger: No such file or directory

On 5.1.y, it has been changed to /sys/devices/platform/leds/leds/orangepi:red:power/trigger

Share this post


Link to post
Share on other sites
3 hours ago, martinayotte said:

On 5.1.y, it has been changed to /sys/devices/platform/leds/leds/orangepi:red:power/trigger

 

Thank you! That worked. Now one of the two LED is off! Way better. 

Share this post


Link to post
Share on other sites
1 minute ago, SchmuseTigger said:

Now one of the two LED is off!

If you mean about the green LED, this other one is /sys/class/leds/orangepi\:green\:status ...

Share this post


Link to post
Share on other sites
14 hours ago, martinayotte said:

If you mean about the green LED, this other one is /sys/class/leds/orangepi\:green\:status ...

Ah thanks! I do have 2 red LEDs. I tried the change from red to green in the command with the change from power to status. There is no error but it does not switch off the second (red) LED in the corner. 

Share this post


Link to post
Share on other sites
5 hours ago, SchmuseTigger said:

There is no error but it does not switch off the second (red) LED in the corner.

Strange !

My OrangePi3 has only 2 LED, one red for power and one green for status. A third green LED is also present on bottom side for PCIe, but it is not turned on by default.

All this is also true according to official schematic ...

 

Share this post


Link to post
Share on other sites
18 hours ago, martinayotte said:

Strange !

My OrangePi3 has only 2 LED, one red for power and one green for status. A third green LED is also present on bottom side for PCIe, but it is not turned on by default.

All this is also true according to official schematic ...

 

well, I just looked at the offical schematics and kinda closed them again, no clue, I see that there is 2 LED (Status / Power) but not anything about the colors. But for sure my 2 LED on the board (there is a yellow one on the Network Port in addition) but on the top side of my board there is 2 red. One went off with the code the other one not with the other one (using Status). 

 

But then again, not that important :)

Share this post


Link to post
Share on other sites

Hi,

 

there seams to be an error in the latest upügrade package

 

dpkg-deb: error: unexpected end of file in archive member header in /var/cache/apt/archives/armbian-firmware_5.86.190514_all.deb
dpkg: error processing archive /var/cache/apt/archives/armbian-firmware_5.86.190514_all.deb (--unpack):
 dpkg-deb --fsys-tarfile subprocess returned error exit status 2
Errors were encountered while processing:
 /var/cache/apt/archives/armbian-firmware_5.86.190514_all.deb
E: Sub-process /usr/bin/dpkg returned an error code (1)

 

ls -la /var/cache/apt/archives/armbian-firmware_5.86.190514_all.deb
-rw-r--r-- 1 root root 544 May 14 18:40 /var/cache/apt/archives/armbian-firmware_5.86.190514_all.deb

 

file size is only 544 bytes

 

thanks and keep up this awesome work

Share this post


Link to post
Share on other sites

Is it possible to integrate wireguard into armbian for opi3, as for banana pi? Currently,

lsmod | grep -i wireguard

returns empty

Share this post


Link to post
Share on other sites
Just now, AZ8 said:

So, should I build image on my box with patch to enable it?


Yes, but future betas will also have it since I enable it yesterday. Waiting will also bring it up.

Share this post


Link to post
Share on other sites

Hi,
I tried to install on my orangepi3 the last image of 05/15/2019

 

https://dl.armbian.com/orangepi3/nightly/Armbian_5.86.190515_Orangepi3_Ubuntu_bionic_dev_5.1.0.7z

 

But it gives me a panic kernel when it does the boot.
So I've gone back to the old version 5.82.190423

 

https://dl.armbian.com/orangepi3/nightly/Armbian_5.82.190423_Orangepi3_Ubuntu_bionic_dev_5.0.7.7z

 

and I've updated with apt-get
When it has rebooted there was the black screen
Before starting the update, the resolution of the display was 1024x768 and its maximum resolution is 1440x900.

 

How do you restore the resolution of the console to 1028x768? I can access to console from another computer via ssh...

 

regards

MaX

Share this post


Link to post
Share on other sites
On 3/30/2019 at 7:45 PM, NicoD said:

Could anyone else check the voltage on USB please? I'm seeing very low voltages of 4.5V idle to 4V maxed out.
I'm using a OPi cable and my 4A PSU from my NanoPi M4. I would like to know if it's my setup. Thank you.
P.S.
With a higher input voltage of 5.3V(vs 5.1V) I get 4.75V idle and 4.5V maxed out.

It's indeed a little low on mine aswell, using the manufacturer's OS it is higher.  I think there is just something set wrong on a voltage regulator? The schematics also seem a little off when it comes to the USB Port: GND is connected to the VCC Pin of the Port and vice versa. I was looking for a voltage regulator there but other than the AXP805 I didn't find one. I looked at the AXP805 Datasheet to see if it could be this one, but as it can't output 5V this can't be it. This leaves 2 options: Either it's connected directly to the 5V Input, so does the armbian OS use that much more power than the manufacturer's OS? Or there is indeed some regulator or protection that is not configured properly at this point.

Share this post


Link to post
Share on other sites
1 hour ago, Flole said:

Either it's connected directly to the 5V Input

The schematic is clearly stating that USB 5V is coming from VDP3/VDP4 which are connected to VCC-5V, therefore directly from DC-IN of the board

Share this post


Link to post
Share on other sites
3 minutes ago, martinayotte said:

The schematic is clearly stating that USB 5V is coming from VDP3/VDP4 which are connected to VCC-5V, therefore directly from DC-IN of the board

The schematic also states that VCC-5V is connected to GND of the USB Connector, thats also not the case here so I am very careful about believing that.

 

Also in the powertree and the Block diagram it has a 12V in connected to a DC/DC Converter. Looking at DCIN that DC/DC regulator is gone. So I am really careful when it comes to reading this schematics....

Share this post


Link to post
Share on other sites
4 minutes ago, Flole said:

Also in the powertree and the Block diagram it has a 12V in connected to a DC/DC Converter. Looking at DCIN that DC/DC regulator is gone. So I am really careful when it comes to reading this schematics....

Are you looking at the wrong schematic ?

OrangePi3 != OrangePi-RK3399 !!!

Share this post


Link to post
Share on other sites
Just now, martinayotte said:

Are you looking at the wrong schematic ?

OrangePi3 != OrangePi-RK3399 !!!

Nope, it clearly says Orange_PI-3 on it, downloaded from the Google Drive. Dated at November 26th 2018.

Share this post


Link to post
Share on other sites
39 39