Rockchip
Quick links to search tags:
Banana Pi M7, BIGTREETECH CB2, Khadas EDGE2, Libre Renegade, NanoPC T6 LTS, NanoPi M5, NanoPi M6, NanoPi R3S LTS, NanoPi R4S, NanoPi R6S, NanoPi R6C, NanoPi R76S, Odroid M1, Orange Pi 4 LTS, Orange Pi 5, Orange Pi 5 Plus, Pinebook Pro, ROCK 5A, ROCK 5B, ROCK 5C, ROCK 5 ITX, ROCK PI E, ROCK PI S, ROCK S0, Zero 3W/3E, RockPRO64, Tinkerboard
-
Per Radxa here, it is possible to obtain CPU temperature via "sudo cat /sys/class/thermal/thermal_zone0/temp". But the following paths do not exist on Armbian 23.05.1 Bookworm with Linux 6.1.30-rockchip64: /etc/armbianmonitor/datasources/soctemp /sys/devices/virtual/thermal/thermal_zone0/temp Running armbianmonitor -M, also does not show the temp: Time CPU load %cpu %sys %usr %nice %io %irq C.St. 22:29:52 408 MHz 0.02 0% 0% 0% 0% 0% 0% 0/6
-
Hello! Does anyone, and by anyone I probably really mean @balbes150 :D, know what I need to do when building official Mesa for it to be recognized in the experimental 6.x kernel environment? There's a panfrost focused dev/staging branch that the panfrost devs are using that I would love to try and be able to build for OPi5 but when I do it I always just get llvm. balbes, you are managing to get the GPU recognized would you be able to share how that's done in the building? I'm not asking for you to provide a build I would just love to know how you do it so I can as well and test the new versions as they happen. This is the branch and commits…
-
Looking for information on enabling 4 wire SPI on the Libre Renegade. I think have it enabled (spi-spidev) in armbian-config and I think configured correctly in /boot/armbianEnv.txt: param_spidev_spi_bus=0 param_spidev_spi_cs=0 param_spidev_max_freq=1000000 Connecting to pins GPIO pin# 19/21/23/24 I still do not see ANY devices matching /dev/spi* - An guidance as to WHY? I have the build framework, but am new to building armbian kernels but could navigate it with some direction. TIA folks! [Trying to connect a 240x320 LCD display using the ST7789-VW controller, not using Arduino IDE]
-
Reputation Points
- 4 replies
- 4.7k views
- 1 follower
-
-
$ neofetch ubuntu@orangepi5 ---------------- █ █ █ █ █ █ █ █ █ █ █ OS: Armbian (23.11.0-trunk.145) aarch64 ███████████████████████ Host: Orange Pi 5 ▄▄██ ██▄▄ Kernel: 6.6.0-rc1-edge-rockchip-rk3588 ▄▄██ ███████████ ██▄▄ Uptime: 4 mins ▄▄██ ██ ██ ██▄▄ Packages: 427 (dpkg) ▄▄██ ██ ██ ██▄▄ Shell: bash 5.2.15 ▄▄██ ██ ██ ██▄▄ Terminal: /dev/pts/0 ▄▄██ █████████████ ██▄▄ CPU: (8) @ 1.800GHz ▄▄██ ██ ██ ██▄▄ Memory: 196MiB / 15718MiB ▄▄██ ██ ██ ██▄▄ ▄▄██ …
-
I download the following image and encountered serious problem; Armbian_23.8.1_Orangepi5_bookworm_legacy_5.10.160_cinnamon_desktop.img.xz The problem is that after screen blank out, 8 CPU cores get near full 100% usage and OPi5 gets very hot. They all have the following htop profile. Pri NI VIRT SHR S CPU% Command 20 0 5725M 224M R 96% cinnamon -- replace
-
The problem persist on both Armbian 23.8 bullseye and Armbian 23.11.0-trunk.107 Bullseye After change it via armbian-config It stays the default cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to cpufreq@vger.kernel.org, please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 1 2 3 CPUs which need to have their frequency coordinated by software: 0 1 2 3 maximum transition latency: 149 us. hardware limits: 408 MHz - 1.99 GHz available frequency steps: 408 MHz, 600 MHz, 816 MHz, 1.10 GHz, 1.42 GHz, 1.61 GHz, 1.80 GH…
-
I have 23.8.1 Jammy installed with kernel 5.10.160 and I'm getting plenty of kernel errors during any video playback, and these also cause the playback to freeze. From my research, these error messages come from librga - which I assume come from the panfork and rockchip repos but I was wondering if anyone has been able to resolve these errors.
-
Reputation Points
- 0 replies
- 3.1k views
-
-
Standard install - Armbian Bookworm, full 'firmware install'. I am getting some packet loss over the LAN. A raspberry pi, Synology NAS and Deban x86 install on the same LAN do not seem to exhibit the same loss. Anyone have experience or ideas? Oddly enough this never seems to occur on fresh installs. This is a docker host for pihole and home assistance, no other packages are really installed at all. I've not really tried much, but since this is a standard install, apt-get update & upgrade are about the only modifications outside of docker install that has occurred. 1. This plugs directly in to a Ubiquiti switch 2. I have tried a few differ…
-
Hello everyone, I recently installed my orangePi 5 to pass workload from my x86 servers over to the orangePi. My main focus is to reduce my overall energy consumption of my homelab. TL;DR Kernel thinks, that while being idle the sweet spot for the frequencies in "ondemand" and "schedutil" is: 1024MHz on the small chips (CPU0-3) 816MHZ on the big chips (CPU4+5, CPU6+7) Reason is an internal cost calculation power vs. frequency gain, which sorts out the lower frequencies. Long story: After getting my first orangePi5 in place, I started to play around with the hardware. I am running: █ █ █ █ █ █ █ █ █…
-
Reputation Points
- 7 replies
- 9.2k views
- 1 follower
-
-
Hi, I would like to use my usb wifi adapter from my old Raspi 3. `lsusb` shows: `Bus 007 Device 002: ID 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapter` `ip a` shows: ``` 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000 link/ether 76:ac:9a:1c:50:76 brd ff:ff:ff:ff:ff:…
-
Every time I stop and then start Chromium, do a search on google, or on youtube, there seems to be a deletion of the cookies, and it asks consent again, login again .... I found lots of possible solutions on internet about that issue, but none work for me! I wonder what this is due to, any ideas?
-
I am trying to compile a new kernel in order to support some satellite receiver tuner (from TBS). I did that successfully (In February 2023) on Orange Pi 5 with Linux kernel 5.10.110, but I am struggling doing it with Orange PI 5 Plus with Linux 5.10.160 (jammy). Basically I would like to turn as Modules lots of CONFIG_VIDEOBUF2_*, in order to replace the modules with the ones compiled separately (that I know are working fine with my TBS USD card). These are my issues: - I do not manage to set separately those CONFIG_VIDEOBUF2_* through the menu config. - Thus I tried to set the whole "multimedia support" as a module and go…
-
I'm looking for information about the Ethernet chip on the Orange Pi 5. I need an SBC that has PTP hardware timestamp support (IEEE 1588). According to OrangePi.org, the Orange Pi 5 has the Motorcomm YT8531C, but I have not been able to find documentation that provides the answer about hardware PTP support. Most likely it does not, but I'd like to confirm on an actual device before purchasing one. If you have an Orange Pi 5, you can test this with this command: ls /sys/class/net |xargs -n1 ethtool -T If there is someone that is willing to run this command and post the output, I would appreciate it very much. Note: This is a cross-post from iot.stack…
-
Reputation Points
- 7 replies
- 10k views
- 1 follower
-
-
Hi! I need to make sure that my GPIOs remember the last state when my Tinkerboard reboots. Is it possible to modify the bootloader and avoid GPIO.cleanup? If yes, then how? Thanks!
-
Reputation Points
- 0 replies
- 1.7k views
- 1 follower
-
-
I don t know for sure a wireless keyboard which works with the Orange Pi 5. Crosstalk Solutions says on his YouTube channel that the Rii (Upgrade) i4 Mini Bluetooth Keyboard with Touchpad, Blacklit Portable Wireless Keyboard with 2.4G USB dongle for Smartphones, PC, Table works with the Orange Pi 5: https://kit.co/crosstalk/orange-pi-5 But Crosstalk Solutions does not show a proof of function in his video, and I don t know anybody else who confirms a wireless keyboard who is working with the Orange Pi 5. Do you know a wireless keyboard?
-
Reputation Points
- 4 replies
- 6.2k views
- 1 follower
-
-
Hi, newbie here again.... I recently switched to Armbian from Orange Pi Ubuntu. I am running Armbian 23.8.1 Jammy with Linux 5.10.160-legacy-rk35xx My issue is a noticeable slowdown in NVME performance. I now get 522.35 MB/sec (as per hdparm test), but before on orange pi ubuntu it was around 1900 MB/s . FYI...Armbian is installed on and booting from the NVME. everything else seems to work perfect and I don't get smartctl errors. Please advise - Crucial P3 4TB PCIe M.2 2280 SSD NVMe (PCIe Gen 3 x4) - Have all the latest updates /dev/nvme0n1: Timing cached reads: 7988 MB in 2.0…
-
Reputation Points
- 10 replies
- 13.6k views
- 1 follower
-
-
Are there any USB WiFi adapters that are supported out of the box? Nothing fancy, just looking for a cheap readily available USB WiFi adapter that doesn't require finding kernel headers and downloading modules to compile that will then be wiped out by the next release. I am currently using Armbian_23.02.0-trunk.0220_Orangepi5_jammy_legacy_5.10.110_xfce_desktop.img installed and booting from a 256GB NVME drive. Ethernet is an option but I'd like to make it more portable. What have you guys used and had success with? My network is WiFi 6+ but not having the best speed is just fine. Thanks in advance.
-
Reputation Points
- 22 replies
- 48.1k views
- 4 followers
-
-
altho there is no warning in the corner any more youtube is a slideshow, or if i am missing something please tell me what or how to enable it.
-
Reputation Points
- 6 replies
- 5.3k views
- 1 follower
-
-
I'd like some help please. The ethernet device naming seems inconsistent. Sometimes one interface comes up as eth0 and sometimes as eth1, and sometimes not at all. The enp1s0 interface seems to reliably come up, but not with the right config (sometimes it uses the config for enp1s0 and sometimes for eth0). I am trying to assign status IP addresses (on different networks) to each interface, but because of the unreliable bringup of the network interfaces, I can't get a config that starts up correctly and consistency on reboots or cold boots. As a test I ran the friendly-core-lite-focal from FriendlyCore and it does not have this i…
-
Armbian 23.08.0-trunk Bookworm with Linux 5.10.160-rk35xx root@orangepi5-plus:~# gpio -v gpio version: 2.46 Copyright (c) 2012-2018 Gordon Henderson This is free software with ABSOLUTELY NO WARRANTY. For details type: gpio -warranty * Device tree is enabled. *--> Orange Pi 5 Plus root@orangepi5-plus:~# gpio readall wiringPiSetup: mmap (GPIO) failed: Operation not permitted
-
Reputation Points
- 3 replies
- 3.7k views
- 1 follower
-
-
Hi everyone!👋 I would like to turn off the leds on my Orange Pi 5. I already tried this with no success, since I can't find the mentioned files (I have /sys/class/leds/status_led instead of red/orangepi etc.). Any tips? Thank you in advance! 🙂
-
Reputation Points
- 7 replies
- 16.8k views
-
-
Hi! I'm using armbian Jammy on my orange pi 5 with installed xfce desktop. I'm trying to connect it to a small HDMI screen and it doesn't work. It shows "no signal". I tried to use another screen (different model, resolution, manufacturer etc.) and it works. Then I tried to use non working screen with jetson nano and it works without any actions. So, the problem is with orange pi with armbian and this specific screen. Here is the result of "xrandr -display :0" launched trough ssh: Screen 0: minimum 320 x 200, current 1024 x 600, maximum 16384 x 16384 HDMI-1 connected primary 1024x600+0+0 (normal left inverted right x axis y axis) 476mm x 268mm 1024…
-
Please advise (see low/high values): nvme-pci-0100 Adapter: PCI adapter Sensor 1: +31.9°C (low = -273.1°C, high = +65261.8°C) Sensor 2: +39.9°C (low = -273.1°C, high = +65261.8°C) Sensor 8: +31.9°C (low = -273.1°C, high = +65261.8°C)
-
I received my new orange pi 5 plus. I installed the official Orange PI 5 Plus Ubuntu on a SD card and it worked great. Then I installed the "Armbian_23.8.1_Orangepi5-plus_jammy_legacy_5.10.160_gnome_desktop" on SD card (Yes I took the image from the page with the "archive for orange Pi 5 plus"), and it get stuck on a screen displaying "Orange PI" (I do not see any armbian logo) , and nothing else happens (the blue light on the board does not blink). Why is that? How can I see what is happening? I installed in the past Armbian on an Orange Pi 5 with no issue, so I am really wondering what is going on there. Your view/ideas w…
-
I need to move my homeassistant from rpi4 to an opi5 but I have some I2C sensors connected. Had anyone any luck configuring python and gpio to work with I2C sensors? This was a bit rough a while ago and the kernel support seems much more limited compared to the rpi4 for this type of use case. Any experience?
-
Reputation Points
- 4 replies
- 4.7k views
- 1 follower
-
-
/boot/armbianEnv.txt rebooting pwm all display working fine
-
Reputation Points
- 4 replies
- 9.3k views
-
-
Hi, my orange pi 5 plus cant boot armbian, its hang and screen goes flicker, im currently not been able to boot android images to (its hang and flicker to),, i cant boot armbian and android version.. but other linux is normally booting fine.. any advise?
-
Reputation Points
- 2 replies
- 3.4k views
- 1 follower
-
-
as the title says i used latest build of armbian cinamon for opi5 and i am tryin to set thing up but chromium is basicaly useless since its reset everytime its closed. i had older armbian build on ssd and after few updates chromium started doing same thing so i guess its not the armbian but some fail within chromium? anyone knows whats wrong with it or how to fix it? so what i mean by useless is it doesnt remeber any logins or passwords so if i open it 100 times i have to login 100 times. thanks for any help
-
Hello to all, I am using an HDMI switch. I have noticed that TinkerBoard Armbian, displays fine the UBOOT text/logo but after that, the HDMI shows no signal/image If I connect the HDMI cable directly from the board to the monitor all is ok. What would be the reason or setting to be changed so TinkerBoard HDMI port can output display either case (hdmi direct to over a hdmi switch) tx in advance
-
Reputation Points
- 2 replies
- 3.2k views
- 1 follower
-
-
Hi all, Is anyone here good with upbringing MIPI panels on Linux via device tree modifications? I've had an attempt with a specific LCD panel but I am not having any luck to be honest. I would love someone to kindly review my Git Diff/device tree changes for any errors. I've attached my LCD init code as well, as well as the DSI portion of the dmesg output log, as well as my schematics for the custom driver board I have designed. https://drive.google.com/file/d/18E5zOGlNpdWLrD43R7bB4N-Mf_8mQFKY/view Thank you! DSI_Debug_Log.txt
-
Reputation Points
- 0 replies
- 1.6k views
-
-
Any guidance on getting the native 2-pin fan connector and control working with Armbian Jammy? e.g. using pwm-fan driver to control the fan. Thanks for any help, please be kind, I'm a newbie 🙂
-
Reputation Points
- 2 replies
- 6.9k views
- 1 follower
-
-
Hello community! Orange pi 4 LTS with Armbian 22.11 Jammy CLI, there is a problem with launching the screen with resolutions: 1024x600 - there is no image 1024x768 - the image is there, there are ripples 1920x1080 - everything is fine Tell me how to solve this problem. uname -a Linux orangepi4-lts 5.15.80-rockchip64 #22.11.1 SMP PREEMPT Wed Nov 30 11:12:47 UTC 2022 aarch64 aarch64 aarch64 GNU/Linux /boot/armbianEnv.txt verbosity=1 bootlogo=false overlay_prefix=rockchip fdtfile=rockchip/rk3399-orangepi-4-lts.dtb rootdev=UUID=72cc3f82-2e76-4495-99fd-8cc46a4a21db rootfstype=ext4 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u …
-
Reputation Points
- 2 replies
- 4.3k views
- 1 follower
-
-
I'm running armbian 23.08 bookworm on an orange pi 5 plus. I'm trying to run VMs that boot with UEFI, but these are hanging. I suspect a bug in the vendor kernel (5.10.160-rk35xx), since this works fine on an AWS bare metal arm64 host. Example: ``` $ sudo apt install qemu-system qemu-efi-aarch64 ... $ cp /usr/share/AAVMF/AAVMF_VARS.fd ./aavmf_efivars.fd $ qemu-system-aarch64 \ -machine virt \ -cpu max \ -drive if=pflash,unit=0,format=raw,readonly=on,file=/usr/share/AAVMF/AAVMF_CODE.fd \ -drive file=aavmf_efivars.fd,format=raw,if=pflash -net none \ -nographic \ -enable-kvm …
-
Reputation Points
- 2 replies
- 4.2k views
- 1 follower
-
-
I have compiled with Armbian build (btw i reported that RockPro64 and Rock64 download pages give 502 Bad gateway) 1. Armbian_23.08.0-trunk_Rockpro64_jammy_current_6.1.46_minimal.img 2. Armbian_23.08.0-trunk_Rockpro64_jammy_current_6.1.46_cinnamon_desktop.img With SPI disabled, the img boots fine, but when reboot/restart takes place, board gives black screen, no U-boot activity, no white light. It will boot again after restart if reset pressed or power off/on Shouldnt board reboot normally? PS nd after u-boot log/text this screen shows prior booting
-
Hi to all, In the past it was proposed by @Igor to use the u-boot-sunxi/remove-boot-messages-from-hdmi.patch this now as I can see under the allwinner-optional and seems do nothing on RockPro64 u-boot compile to hide the text @jock provided in the Tinker forum a userpatch disable-vidconsole.patch which works great on it (tinker) diff --git a/include/configs/tinker_rk3288.h b/include/configs/tinker_rk3288.h index bde7d72e6d..3ae9bb05f7 100644 --- a/include/configs/tinker_rk3288.h +++ b/include/configs/tinker_rk3288.h @@ -7,9 +7,9 @@ #define __CONFIG_H #define ROCKCHIP_DEVICE_SETTINGS \ - "stdin=serial,usbkbd\0" \ - "stdout=ser…
-
Hello, Armbian 22.02 images doesn't boot on rockpro64. I have tried: Armbian 22.02 Bullseye Armbian 22.02 Jammy XFCE It doesn't boot (not blinking white led). Previous builds works correctly: Armbian_21.08.1_Rockpro64_bullseye_current_5.10.60
-
Reputation Points
- 10 replies
- 6.4k views
- 1 follower
-
-
Hello Everyone, As I am still working on hardening my Odroid-M1 servers, I am looking for a solution to activate a real console for root login only. My homelab is not in the same room as my desk, so I need to get access from an internal VLAN with restrictions and take control even if the network drivers are not enabled. Have you tested or used a UART to Ethernet converter like https://www.pusr.com/products/ethernet-to-uart-modules-usr-k7.html or https://www.waveshare.com/uart-to-eth.htm or something else? Let me know your thoughts. Sincerely, Frederic
-
Reputation Points
- 6 replies
- 4.2k views
- 1 follower
-
-
Hello all, Is there any chance to run mainline kernel? Support for rk3588 seems to be starting with 6.2 and 6.3 (mainline has dts for rock 5b).
-
Reputation Points
- 8 replies
- 8.9k views
- 4 followers
-
-
Hello, The issue I describe below begins with a simple 1GB/s speed test with iperf3 (using tcp, then udp). With tcp everything is almost ok. With udp it's an other story. I first try through Internet and notice that there is connection drops. The network topology is : test computer => internet => router => switch (Mikrotik crs-326) => Rockpro64 The iperf3 server is on Rockpro64, and the client is on test computer. I then try to narrow down : - I connect directly to the switch and try again : in and out switch ports show near max speed (~1 Gbps), however the iperf3 server logs show 2 or 3 transfers at reduced speed, then show no tran…
-
Reputation Points
- 0 replies
- 2.3k views
- 1 follower
-
-
Hello everyone, I'm a newcomer to ARMBIAN, and I'm eager to transition from my current stock Odroid (20.04) setup (petitboot full nvme SSD) to a more up-to-date distribution, complete with the latest kernel upgrades. I've taken the time to go through the documentation and here's what I've gathered: It appears that native booting from an nvme SSD or USB isn't possible (yet?). Instead, I'll need to use microSD cards or an emmc module for booting while installing the system on an nvme SSD. I also understand that deactivating petitboot is necessary. Now, I have a few questions: Q1: Do I have a correct understanding of these two p…
-
Reputation Points
- 0 replies
- 2.6k views
- 1 follower
-
-
hi all, so i skipped i beleive 2 releases of armbian for opi5 and i just downloaded latest and installed. i am not english native and armbian installs local langauge automaticaly wich is ABSOLUTELY NOT WANTED and quite annoying from my perspective. what i need is just plain en.us or english internatinal for system and keyboard but i cant get it. i tried changing it with armbian config but it doesnt do a thing, local language is always there and its a huge PITA. please armbian dudes, return to manual selection, i beg you. any tips how i can fix it so its just plain english? or how can i force installation to ask me what language to choose? thanks for an…
-
Hello, thanks for supporting this device I'm trying to install pivccu (homematic smarthome) on armbian to use it with homeassistant. It's not officially supported (yet) but I got it running with the default hardkernel ubuntu image. https://github.com/alexreinert/piVCCU/blob/master/docs/setup/armbian.md I can't seem to find the kernel headers/sources for my kernel. Any Ideas? Below is what I found. I'm willing to go back to 6.1.12 if that doesn't cause any issues. Can't do it via armbian-config. Do I need to download an image from the archive and reinstall? uname -a Linux odroid 6.3.4-rk3568-odro…
-
Reputation Points
- 0 replies
- 3k views
- 1 follower
-
-
Hi Please, find below my current Armbian version in OPI5: Armbian_23.5.5_Orangepi5-plus_jammy_legacy_5.10.160_cinnamon_desktop I’m having a few issues with Orange pi 5 Plus. Wifi/Bluetooth issues: I bought this WIFI/Bluethooth model (RTL8852BE) ( Link ) Bluetooth: When I try finding a new dispositive does not find anyone. However, it’s working with Ubuntu. WIFI: I did not have any problem with SDcard but the NVME gave me wifi problems sometimes when I updated it with “apt upgrade”. Then, the wifi does not work and I have to reboot and switch off bluetooth to make the wifi work. I…
-
/root/RTL8811CU/os_dep/osdep_service.c: In function ‘rtw_change_ifname’: /root/RTL8811CU/os_dep/osdep_service.c:2494:28: warning: passing argument 1 of ‘_rtw_memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers] 2494 | _rtw_memcpy(pnetdev->dev_addr, adapter_mac_addr(padapter), ETH_ALEN); | ~~~~~~~^~~~~~~~~~ /root/RTL8811CU/os_dep/osdep_service.c:925:24: note: expected ‘void *’ but argument is of type ‘const unsigned char *’ 925 | void _rtw_memcpy(void *dst, const void *src, u32 sz) | ~~~~~~^~~ /root/RTL8811CU/os_dep/osdep_service.c: In function ‘rtw_random32’: /ro…
-
Hello, i have a question about how to configure a 7' touchscreen, in my case i bought this: https://es.aliexpress.com/item/1005004163930837.html?spm=a2g0o.order_list.order_list_main.50.57c1194d914MA4&gatewayAdapt=glo2esp but the the problem is when i connect to my Orange Pi 5, on my laptop the screen works very well but in orange pi 5 with Armbian Jammy 23.5.5 Cinamon and it doesn't recognize it. Is there a solution on how to connect it?
-
Reputation Points
- 3 replies
- 3.1k views
- 1 follower
-
-
Hi folks, Ran into some issues with July 6 bookworm images for Orange Pi 5 Plus - it boots but there is no video or network. Orange Pi 5B has a note to change the dtb - one is also needed for the 5 Plus. It should be `fdtfile=rockchip/rk3588-orangepi-5-plus.dtb`. (I tried to search for related issues, but the rate limit is stopped me so I gave up.)
-
Hi. By updating the system today caused the hardware acceleration to fail. Start-Date: 2023-08-04 12:26:33 Commandline: apt upgrade Upgrade: armbian-jammy-desktop-gnome:arm64 (23.02.2, 23.08.0-trunk--1-Vf900-B4c8e), system-monitoring-center:arm64 (1.43.9, 1.43.10), ufw:arm64 (0.36.1-4build1, 0.36.1-4ubuntu0.1), libmutter-10-0:arm64 (42.9-0ubuntu1, 42.9-0ubuntu4), libpoppler-cpp0v5:arm64 (22.02.0-2ubuntu0.1, 22.02.0-2ubuntu0.2), mutter-common:arm64 (42.9-0ubuntu1, 42.9-0ubuntu4), poppler-utils:arm64 (22.02.0-2ubuntu0.1, 22.02.0-2ubuntu0.2), libpoppler-glib8:arm64 (22.02.0-2ubuntu0.1, 22.02.0-2ubuntu0.2), gir1.2-mutter-10:arm64 (42.9-0ubu…
-
Reputation Points
- 6 replies
- 7.1k views
- 1 follower
-
-
Hi I have been trying to install root file on btrfs using armbian-config from sd card to nvme The process completed successfully but cannot boot. (Note that I have also modified armbianEnv.txt from etx4 to btrfs) The same process works on ext4 Appreciate if someone can give some pointer to get this working
-
Reputation Points
- 0 replies
- 1.6k views
-
-
Hi I want to use the I2S GPIO output pins ( 26 pins ) on Orange Pi4 LTS to connect multi channel DAC. Is it possible to overlay some pins?
-
Reputation Points
- 5 replies
- 6.8k views
- 2 followers
-
-
Guys, i'm new. I enabled the sata module in armbian-config then i did sudo dd bs=1M if=/path/your/armbian.img of=/dev/sda status=progress && sudo sync overlays=opi5-sata is in mnt/boot/armbianEnv.txt Without the sd, the orangepi boots in initramfs. I've added a screenshot with the shell output on hdmi. I can boot from SD but that's not what i need. Any thoughts whats going on?
-
Reputation Points
- 6 replies
- 6.7k views
-
-
I will receive soon a Orange Pi 5 Plus. I have setup completely an Orange PI5 with Armbian. I had to recompile kernel, compile drivers ...... it took some time. If I run the Orange PI5 plus with the same SD card as the Orange Pi 5, would it work? If not, is there an easy thing to do to make it work? I think there is a device tree file hardware specific , but is it read when compiling the kernel or dynamically? I am asking because processors are very similar, and it would make my life easier! Your view will be appreciated. Thanks.
-
I've setup the pwm overlay but while it shows up the pwm devices in /devices - it is missing the pwm0 control I've read couple posts where ppl have been able to override the overlays by decompiling the original one, but I can't make sense of the dtc dtb dtbo and dtsi files 😕 Any guides or other suggestions to fix the pwm control? Temperature and fan control on OPI5 - Orange Pi 5 / 5B / 5 Plus - Armbian Community Forums Rock Pi4 pwm control - no overlay? - Rockchip - Armbian Community Forums
-
Reputation Points
- 1 reply
- 2.2k views
- 1 follower
-
-
I built apt packages for the OPI 5 wiring pi and have them hosted in lauchpad https://launchpad.net/~erik1220/+archive/ubuntu/wiringpi-opi Any way to contribute them to the official build? Btw apt-add-repository is broken on 25.8 - I assume it is a side effect of python 3.11... seen similar errors on ubuntu
-
Reputation Points
- 0 replies
- 1.8k views
- 1 follower
-
-
If anyone is looking at fixing the access for gpio and i2c - I found you can fix it with the following udev rules addgroup --system i2c addgroup --system gpio create in /etc/udev/rules.d/60-i2c-tools.rules SUBSYSTEM=="i2c-dev",KERNEL=="i2c*", GROUP="i2c", MODE="0660" create in /etc/udev/rules.d/61-gpio-tools.rules SUBSYSTEM=="gpio",KERNEL=="gpiochip*", GROUP="gpio", MODE="0660"
-
Reputation Points
- 0 replies
- 2.6k views
- 1 follower
-
-
Hi, what is the appropriate way to upgrade from the earlier 23.5.1 to the latest 23.5.5 on the orange pi 5? Thanks
-
Has anyone successfully migrated from 23.2 (stable) to 23.5 (stable)? Is that scenario possible today? I'm looking to get the Bluetooth working, I know it has been fixed in 23.5 but that one is currently broken.
-
Reputation Points
- 3 replies
- 3k views
- 1 follower
-
-
Hello! Has anyone tried to play straight unconverted hevc video from a GoPro 11? Iv'e tried ffplay and gst-play but I'm just getting a static image and a bunch of these errors, [swscaler @ 0x7f49d399c0] [swscaler @ 0x7f49d47a50] deprecated pixel format used, make sure you did set range correctly I have successfully played example jellyfish videos of hevc and hevc 10bit formats, ffmpeg reports the following details from the GoPro footage, Stream #0:0[0x1](eng): Video: hevc (Main) (hvc1 / 0x31637668), yuvj420p(pc, bt709), 3840x2160 [SAR 1:1 DAR 16:9], 119725 kb/s, 119.88 fps, 119.88 tbr, 120k tbn (default) …
-
I got my Orange Pi 5 board to boot v6.1.20 I took all the patches from here: https://gitlab.manjaro.org/manjaro-arm/packages/core/linux-rk3588/-/tree/main/ and built from Armbian's latest trunk source. These patch(es) will need to be modified to support v6.2 & v6.3. > uname -a > Linux orangepi5 6.1.20-rockchip-rk3588 #trunk SMP Tue Apr 25 11:47:11 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux
-
On my Orange Pi 5, I have successfully installed the X11VNC server. I followed the guide at the following link X11VNC and everything works as expected. I can connect with Real VNC from another device and see the desktop of the Orange Pi as if I were in front of its display. However, when the Orange Pi 5 is powered on without a display connected to the HDMI port, the access with Real VNC doesn't work as before. I get a black screen and I am unable to interact with the Orange Pi. I had a similar issue with Raspberry Pi, where I could resolve it by setting a default screen resolution. How can I achieve this with Armbian? How can I configure an alternative resolution when the…
-
Reputation Points
- 2 replies
- 8.3k views
- 1 follower
-
-
Anyone have any success getting this module for new MediaTek WIFI 6 adapters? I've tried this backport of the mainline driver but get this compilation error. https://github.com/astsam/mt7921/issues/1 Anyone any ideas?
-
Reputation Points
- 5 replies
- 6.2k views
- 1 follower
-
-
Thank you all for this series of notes. I have been operating Armbian 22.08 successfully using the sd card on my PBP and like it BUT I would like to boot from emm. I have tried dozens of ways to install it to no avail. Seems to be associated with the rootdev=UUID=... If I use the UUID provided in the Armbian-install then I can boot from emm but it ends up mounting and running from the SD partition. Is there any code that can be inserted into the /boot/armbianEnv.txt file that would provide better diagnostics? To me it appears as if the emm partitions UUID is not available at boot time. Thanks, Carl
-
Reputation Points
- 6 replies
- 7k views
- 2 followers
-
-
Hi there, I've been using ARMbian for a couple of years now under a Rock Pi S board. I'm using an ARMbian OS image based on kernel 4.4x because it have a virtual wlan interface called P2P0, this allow me to use the board as WiFi repeater, I've written a post about it here. However, in recent ARMbian OS images with kernel 5.x and 6.x that virtual interface isn't there. I see in ARMbian OS image with kernel 6.x that the WiFi Hotspot set up menu in the armbian-config tool show an interface called p2p0-dev, but it doesn't work. My question: why? these newer kernels have limitations on this board? or maybe need to compile the kernel with custom modifications?. …
-
Reputation Points
- 0 replies
- 2.5k views
- 1 follower
-
-
Hi, does anyone know how to get hardware video acceleration on orange 4 lts? I've looked around and I saw that rk3399's multimedia support can be enabled using the rk3399 legacy multimedia framework. But that requires a legacy buster image, which doesn't exist for the orange pi. I've tried to compile it myself, but it seems the compile script won't allow it. Is it really impossible to compile a legacy kernel for orange pi 4 lts?
-
Reputation Points
- 4 replies
- 5.6k views
-
-
Loading the latest dist with 5.10.160 kernel, the header package has wrong version...
-
I tested boot time and node-red-reboot time and noticed that boot-time is with bookworm ~2 sec and node-red-reboot got from 14sec to 20sec. I hope you can improve performance so I can upgrade. https://paste.armbian.com/uhocorarad
-
Reputation Points
- 0 replies
- 2.4k views
-
-
With the prior image and kernel 5.10.110 I was able to run compile.sh and produce the linux-source-legacy-rockchip-rk3588_23.02.0-trunk_all.deb which provided the kernel source in /usr/src/linux-source-5.10.110-rockchip-rk3588.tar.xz. I downloaded the latest img which provides kernel 5.10.160 which booted fine. However, running the same compile.sh process I used previously with success produced the older deb package that contains the 5.10.110 kernel source. There were a couple of errors displayed. My compile.sh command is: ./compile.sh BOARD=orangepi5 BRANCH=legacy BUILD_ONLY=kernel RELEASE=jammy KERNEL_CONFIGURE=no The first error encountered was …
-
I was able to flash armbian bookworm cli to the ssd using balena etcher but when I boot the OPI5 from the sdcard and run lsbk it can only see the sdcard any ideas ...
-
I'm running Armbian Jammy (23.02.2) aarch64, Xfce 4.16, Kernel: 5.15.93-rockchip64 on a Libre Renegade and would like to change the resolution to 1360x768. I have tried the Display Settings which only has 1280x720 and I can't change the scale, also I have tried changing the values in Settings Editor but that doesn't change anything. (DISPLAY=:0 xrandr -q) shows: xrandr: Failed to get size of gamma for output default Screen 0: minimum 1280 x 720, current 1280 x 720, maximum 1280 x 720 default connected 1280x720+0+0 0mm x 0mm 1280x720 0.00* I have limited experience with XFCE and terminal commands, any help is appreciated thanks.
-
Reputation Points
- 6 replies
- 4.1k views
- 2 followers
-
-
Is there any existing solution how to use SPI2 on Radxa Rock Pi S? In dmesg I found these messages: [ 1.619008] rockchip-pinctrl pinctrl: pin gpio1-22 already requested by ff0c0000.serial; cannot claim for ff140000.spi [ 1.619046] rockchip-pinctrl pinctrl: pin-54 (ff140000.spi) status -22 [ 1.619065] rockchip-pinctrl pinctrl: could not request pin 54 (gpio1-22) from group spi2-miso on device rockchip-pinctrl [ 1.619082] rockchip-spi ff140000.spi: Error applying setting, reverse things back Is it somehow possible to disable the serial port which is in collision with the SPI? There is a log from armbian monitor: http://…
-
My experience so far: 1. Booting up (Jammy/Bullseye) from SD, HDMI out to 1440p display cuts off text at the bottom. It affects installation and later use. I need to press ENTER several times to all questions until text moves up in the buffer and becomes visible, and then blindly type the answer to proceed to the next step, then several ENTERs to scroll again, and so on. Looking at fbset and stty output: me@opi:~$ fbset -i mode "2560x1440" geometry 2560 1440 2560 1440 32 timings 0 0 0 0 0 0 0 accel true rgba 8/16,8/8,8/0,0/0 endmode Frame buffer device information: Name : rockchipdrmfb Address : 0 Size …
-
Reputation Points
- 45 replies
- 26.2k views
- 1 follower
-
-
I noticed the new images with 23.5 but I have an older installation, then went to nightly, I just switched back to the official, I ran dist-upgrade but when I boot, the system shows Armbian 23.02. Am I missing something to get 23.5?
-
Reputation Points
- 6 replies
- 6.2k views
- 1 follower
-
-
I have recently purchased an Orange Pi 4 LTS and attempted to run Armbian 23.02 Cinnamon version on my board. However, I could only able to connect into the network with 2.4Ghz. Everytime when I connect to the 5Ghz Network, it failed with some authentication issues (such as WPA3). I am sorry I am new to Linux.May I ask if anyone now how can I resolve the problem?
-
Reputation Points
- 2 replies
- 4k views
- 2 followers
-
-
I did a fresh install of armbian jammy 23.5 cli on my orangepi 5 (I previously used 22.11 and 23.02), and I cannot reboot. "sudo reboot" just hangs the system. Not really a big deal, just somewhat annoying, because previous versions runs fine. Anybody else experiencing the same problem? "armbianmonitor -U" output is attached. armbianu.txt
-
Reputation Points
- 4 replies
- 3.3k views
- 1 follower
-
-
booted opi5 via nvme one day and the boot screen mentions about btrfs partition missing even tho it was using ext4 partition. booted via sdcard and the root partition is entirely missing on the nvme. the boot partition is still there and working. not sure if relevant but the previous time i shut the opi5 down, i forgot to unplug it and it was plugged in for about an hour after shutdown with the red led and fan on. the nvme is kingspec which while cheap doesnt seem to have that many bad reports online that i can find (the boot partition was fine so i suspect kingspec isnt at fault). the power adapter is a 25w phone charger w/ pd/qs; it hasnt exhibited any weird behavior (l…
-
I am working with a Rock Pi S v1.3 and thus far the only image I have been able to get to boot is Armbian 21.05.9 Focal with Linux 4.4.247-rockpis. I have tried the recent Arabian Bookworm, Armbian Jammy and a few other variations I have come across on various forum posts here. With the above working image I can communicate with it via UART and get to the terminal. With everything else I don't even get the blinking blue LED; just two solid green LEDs. I have a few of these boards and have confirmed this issue across all of them. I am not sure what next steps to take so any pointers would be greatly appreciated. Thank you very much in ad…
-
Reputation Points
- 7 replies
- 5.7k views
- 2 followers
-
-
Hello Armbian forum, I need to have a GPIO interrupt on Orange PI5. I have successfully installed WiringOP and I am using it with C code. The problem is that the interrupt is not working, and I am receiving the following error. How can I proceed? Does anyone know how to enable the WiringOP interrupt on the GPIO PIN? Code C : #define AUX 13 wiringPiISR(AUX, INT_EDGE_FALLING, &MyFunction); Error: wiringPiISR: unable to open /sys/class/gpio/gpio92/value: No such file or directory PS. I have just successfully installed this version: Armbian 23.02 Jammy Gnome
-
Reputation Points
- 7 replies
- 4.5k views
- 1 follower
-
-
root@orangepi5:~# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 0 223.6G 0 disk ├─sda1 8:1 0 256M 0 part /boot └─sda2 8:2 0 221.1G 0 part /var/log.hdd / mtdblock0 31:0 0 16M 0 disk mmcblk1 179:0 0 29.8G 0 disk ├─mmcblk1p1 179:1 0 256M 0 part └─mmcblk1p2 179:2 0 29.2G 0 part zram0 254:0 0 7.7G 0 disk [SWAP] zram1 254:1 0 50M 0 disk /var/log root@orangepi5:~# cat /boot/armbianEnv.txt verbosity=1 bootlogo=false overlay_prefix=rockchip-rk3588 overlays=orangepi-5-sata fdtfile=rockchip/rk3588s-orangepi-5.dtb r…
-
For the Rock PI S, what is the recommended gpio library? I tried using Radxa libmraa but encountered the following errors (using bullseye-stable): $ sudo apt-get install -y libmraa ... The following packages have unmet dependencies: libmraa : Depends: libjson-c3 but it is not installable Depends: python but it is not installable Depends: python2.7 but it is not installable Depends: libpython2.7 but it is not installable Depends: python3.7 but it is not installable Depends: libpython3.7 but it is not installable E: Unable to correct problems, you have held broken packages.
-
Reputation Points
- 2 replies
- 3.9k views
- 1 follower
-
-
Hi, Armbian_23.02.2_Orangepi5_jammy_legacy_5.10.110 works well with my OPI5. I can ssh to and play with it from my Debian desktop. I don't have HDMI monitor so I want to try serial port. i'm using USB-TTL cable to connect OPI5 to my Debian box. Then in Debian bash I use this command to connect to the port screen /dev/ttyUSB0 Then power on the OPI5. The output is garbled: If i change it to cs7 (screen /dev/ttyUSB0 cs7), the output is still something I cannot understand: The stty command and output: $ sudo stty --file=/dev/ttyUSB0 --all speed 9600 baud; rows 0; columns 0; line = 0; intr = ^C; quit = ^\; erase = ^?; kill = ^U; e…
-
Reputation Points
- 15 replies
- 12.2k views
- 1 follower
-
-
For some odd unknown reason. I can not get the following installed and running. (using official os for Opi5) 1- A virtual machine running on armbian. 2- Dolphin emu 3- Waydroid Thx, vandyman
-
Reputation Points
- 1 reply
- 1.6k views
- 1 follower
-
-
After updating my Orange Pi 5 I no longer can use the "opi5-i2c5-m3" overlay in /boot/armbianEnv.txt to activate and use i2c. Seems the file (or any ohter "opi5-i2c*") is gone from /boot/dtb folder. #uname -a Linux 5.10.110-rockchip-rk3588 #1 SMP Sun Apr 2 14:30:48 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux Is there a new or different procedure to activate i2c? Do I need to install a separate package for it? Or build the entire OS? Anyone else having the same issue? It does detect some i2c devices(0,10,2,6,7,9), but they don't seem to be related to the GPIO headers, prevoiusly I could also use (1,3,5). # ls -l /dev/i2c- i2c-0 i…
-
Ok so I think I have this figured out. It doesn't work at all in Armbian 23.05.1 with the 6.x kernel no matter what I try. It does work in the older Armbian 23.02.2 Jammy (kernel 5.15.93) but the given instructions didn't work for me and needed additional commands. I had to enable the rk3328-opp-1.5ghz overlay or else the max frequency was locked to 1296 MHz. I also found the MAX_SPEED value in the instructions to be too low. To get it to work in 23.02.2: First you have to enable the rk3328-opp-1.5ghz overlay in armbian-config (System > Hardware > rk3328-opp-1.5ghz) or just add it to the overlays line in /boot/armbianEnv.txt and reboot. Next open the /et…
-
Reputation Points
- 0 replies
- 2.6k views
- 1 follower
-
-
with clean install of armbian plus those 4 lines to install hardware acceleration glmark2-es2 gives score of about 800-900, about less then 25% of performance opi5 is capable. is it possible to raise that a bit, not all the way but just a bit more without instaling gnome or wayland, just to keep armbian as clean as its possible. as it is, its stable but barely(they do run) able to run 4k youtube oe 4k mkv, as soon as there is gnome and wayland it starts to crash, joshua rieks version, monka, armbian with all the drivers, any i tried it would crash eventualy.
-
Using the 5.xx kernal I have been changing the eth0 MAC address at /etc/NetworkManager/system-connections/ 'Wired connection 1.nmconnection'. This has changed a bit as the versions progress - but version Armbian 21.08.2 Focal / Linux 5.14.5-rockchip64 has now moved the "wired ..." file to the /run/NetworkManager/system-connections/ and suspect the file is recreated at every boot (edits do not stick). I have tried to set MAC at /boot/armbianEnv.txt and in the eth config file. None work. Any ideas as to how to set the MAC address - and is it now even possible?.
-
Reputation Points
- 5 replies
- 6.7k views
- 2 followers
-
-
I am after compiling a module for a wireless card. I got plenty of errors, thus decided to go to the basis and test the creation of a "hello" module. I am using the image: Armbian_22.11.4_Orangepi5_jammy_legacy_5.10.110_xfce_desktop.img vi hello.c ------------------------------------------------- #include <linux/init.h> #include <linux/module.h> static int hello_init(void) { printk("Hello Orange Pi -- init\n"); return 0; } static void hello_exit(void) { printk("Hello Orange Pi -- exit\n"); return; } module_init(hello_init); module_exit(hello_exit); MODULE_LICENSE("GPL"); ------------------------------…
-
Reputation Points
- 8 replies
- 6k views
- 1 follower
-
-
Hey, I’ve read you can save 40Ma, can anyone tell me what is the best way of disabling HDMI? TIA
-
Reputation Points
- 1 reply
- 2.4k views
- 1 follower
-
-
SoC Rockchip RK3588 (8nm LP process) CPU • 8-core 64-bit processor • 4 x Cortex-A76(2.4GHz), 4 x Cortex-A55(1.8GHz) and separate NEON co-processors GPU • Arm Mali-G610 • Built-in 3D GPU • Compatible with OpenGL ES1.1/2.0/3.2, OpenCL 2.2 and Vulkan 1.2 NPU Embedded NPU supports INT4/INT8/INT16/FP16 mixed operation, with up to 6Tops computing power PMU RK806-1 RAM 4GB/8GB/16GB （LPDDR4/4x） Memory • QSPI Nor FLASH: 16MB/32MB • MicroSD card slot: up to 128GB • eMMC socket: 16GB/32GB/64GB/128GB/256GB eMMC module can be attached • M.2 2280 slot for NVMe SSDs (PCIe 3.0 x4) up to 2,000 MB/s USB • USB3.0 × 2 • USB2.0 × 2 • Type-C ×1 Video • 2x HDMI …
-
Reputation Points
- 0 replies
- 7.4k views
- 1 follower
-
-
Hi all, I'm trying to debug a sporadic problem with my Orange Pi 5 (16GB) which I'm unable to reproduce. I'm hoping maybe someone else experienced a similar issue or at least has any pointers on how to debug it further. The problem: At random times of the day, the board just appears to freeze up. All communications stop. Board is powered on, with red LED on and green LED off. I have to manually unplug the device to reset it. Within the last 2 weeks, this happened 3 times already. Each time, the last log appears to be a journalctl flush (example: https://pastebin.com/dDm5Xtis - the board froze at midnight, no more logs until …
-
armbianmonitor output: http://ix.io/4s3z I'm testing Armbian 23.02 Jammy on a Rock Pi S with its matching "PoE HAT" (which provides a 3.5mm headphone jack). No sound cards are available despite the device tree evidently containing sound devices/codecs [1, 2]. aplay output: rockpi-s:~:% aplay -l aplay: device_list:274: no soundcards found... The armbianmonitor/dmesg output contains the following suspicious lines: [ 24.551148] platform acodec-sound: deferred probe pending [ 24.551191] platform sound: deferred probe pending Digging into this a bit further, I found this root@rockpi-s:/home/dale# cat /sys/kernel/deb…
-
Reputation Points
- 11 replies
- 6.7k views
- 3 followers
-
-
Hello, I'm planning on running a k3s cluster with Rook storage with a few of the Orange Pi 5 that I got. A prerequisite for rook however is RBD module. I've been able to recompile the kernel including RBD support, however I've been unable to get the device to boot from the new kernel. Rebooting after kernel has been built and installed still reports Linux 5.10.110-rockchip-rk3588. Any help would be appreciated. I've since wiped the boxes clean and have a fresh install booting from SSD with the OS installed on the NVMe attached so I will be able to provide any information required. Thanks!
-
Reputation Points
- 7 replies
- 5.2k views
- 2 followers
-
-
``` May 21 21:53:26 rpc.idmapd[21345]: main: fcntl(/run/rpc_pipefs/nfs): Invalid argument May 21 21:53:26 systemd[1]: nfs-idmapd.service: Control process exited, code=exited, status=1/FAILURE ``` The rpc.idmapd version in Debian is still ancient (as with many things in debian) and still requires dnotify but the armbian kernel for the orange pi 5 build ``` $ grep -i dnotify /boot/config-5.10.110-rockchip-rk3588 # CONFIG_DNOTIFY is not set ``` It looks like bookworm will likely fix this when it's out, so maybe the right thing to do is simply move to bookworm asap but this does prevent the ability to fully support nfsv4 with…
-
Hello Kind Forum Experts, I ask for you help with following issue: Device: Nanopi-r4s 4GB Background: I'm happy with my device running from SD - but wanted to preemptively upgrade to eMMC based setup for improved reliability. I bought "original" FriendlyELEC SD-to-eMMC adapter + 64GB eMMC module. with normal microSD it boots great, with the sd-to-eMMC - nothing multiple attempts, tried both cloning my old SD & writing fresh image but both didn't help. eMMC type is 1.8V\3.3V HS400 speed, i think i need to address that in the .dtb file ? any help would be much appreciated Uri
-
Reputation Points
- 0 replies
- 3.4k views
- 1 follower
-
-
Hi. Great work with Armbian. Any good advice setting up Wayland and pipewire (for OBS studio) on the Orange pi 5 (23.02 jammy gnome)? I did manage to install both pipewire+pipewire-media-session+pipewire-pulse+related qt5 Wayland package and setting up QT_QPA_PLATFORM=wayland environment variable. But no luck.
-
On my Odroid M1 I have a display that will not work, other displays do work. Unfortunately, I need this display to work. When I plug it in, I see "PHY PLL not locked" in dmesg. If I boot with it plugged in, I see the Hard Kernel logo, then the screen turns off as Armbian boots. I booted into the Ubuntu 20.04 Gnome image provided by HardKernel and that one works. 1. What could I change to allow this display to be detected? 2. Can I just force the board to boot with output to 1024x768@60. I just need the output. Thanks all.
-
Reputation Points
- 0 replies
- 2.2k views
- 1 follower
-
-
For a fresh install of the latest desktop version for OrangePi5 I cannot get the system to run from NVME which is a Samsung 960 Pro. It gets stuck on the spinner at boot for the first-time boot after NVME using SD - NVME in armbian-installer. Any suggestions...
-
404 when trying to download SHA on this link:
-
Hello, I am running Armbian 23.05 "minimal" (with the provided kernel 5.10.110) on my OrangePI 5 4GB. Upgraded all packets to latest. When trying to run GeekBench 5.5.1 ARM Preview, it reboots when approaching the end of multicore tests, with "performance" governor and default speed range (0.4 - 2.4 GHz for A76). Same goes if I drop the max clock speed to 2.2 for A76. After dropping to 2.0 GHz max, it runs fine; but this hurts performances quite a bit. I tried various power sources, including a bench PSU which can reliably supply up to 30A (but I only see a few spikes over 2A). The board has a large heatsink installed wit…
-
My microphone is not working on armbian jammy gnome Device : Opi 5 16GB I tried to use command arecord -l I showed 1 sound card Named rockchip or something like it with similar name.
-
Reputation Points
- 4 replies
- 3.3k views
- 1 follower
-
-
Expected Behavior: I am able to enter sleep mode, either graphically or using systemctl suspend, and then wake from sleep mode by typing on the keyboard or pressing the power button Current Behavior: The system appears to enter sleep fine, but once in sleep pressing the power button or pressing buttons on the keyboard seems to do nothing (pressing keys on my keyboard causes it to light up, however my mouse does not light up). The display remains blank and the green led does not blink. I have to do a forced shutdown by holding the power button or unplugging the power supply. Note: the behavior is the same no matter if I suspend from a desktop sessio…
-
Reputation Points
- 12 replies
- 9.5k views
-
-
I am trying to play some dolby vision movies in Armbian (Orange pi 5) but the colours are not accurate. Do you know if it is possible to play DV movies and how? Thankd
