Beginners

Hi I am looking for tips on how to install OpenCL on RockPro64 running headless Armbian_20.05.4_Rockpro64_focal_current_5.4.46. I don't want to install Xorg, just OpenCL for crypto mining benchmarks.

Hello, I want to use nano pi neo2 as a compiler server (for picture rendering with "Blender") Is it possible to forward X11 via ssh ? What img must I use to do this ? (I don't know if server bionic is suitable to do this) Best Regards, Boris

Hello, I am new on the embedded system. I am using Orange Pi zero and I am having stuff with wlan configuration. I want to run the static ip for wifi on the board and reconnect after every time rebooting How I do that? I use 2 files below The eth0 works fine with this setup otherwise the wlan not active even though I used ifconfig wlan0 up but I using ifconfig wlan0 down, it got the static ip like the configuration file then I can't turn on or off using ifconfig up/down one more time Anyone help me? Thanks a lot!

Hello all, I have a Novasom M7 Plus board with a Rockchip RK3328 that initially had an SD card with Armbian. I made the necessary hardware connections to connect to a screen via HDMI and then I followed all the necessary steps to perform the BOOT through the eMMc memory but after transferring the rootfs it will not start via EMMC, only with the SD card it is possible to start the system. I have tried a lot of solutions that I am finding in the forums but I still haven't been able to solve the problem. The goal is to start Armbian without having the SD card inserted.

I have complied R40 board ( not bpi v40) with Armbian kernel and the u-boot hangs and showing BOOT. I was using u-boot 2014-07 and boot0_sdcard.fex and boot_package.fex for bootloader.

Hi, I'd like to setup log2ram so that it never writes to the disk, but rather discards all logs at shutdown. The documentation for log2ram says that if I delete /etc/cron.daily/log2ram it will only sync the logs to the disk at shutdown. But is there a way to have it not even do that? Also, in order to prevent log2ram from filling up all its space in RAM, is it possible to setup an overwrite mechanism so that the logs begin overwriting themselves once they hit the space limit?

Hi, I run a wireguard server in my home. I have a Mac and a couple of iOS devices that can successfully connect to the server, my internet traffic is routed via the home wireguard server and I can access devices in my home network using an address like 192.168.178.200. No problem. Now I want to connect my cubitruck running Armbian Ubuntu 18.04 to my home network. I created a similar configuration as for all of the other devices, wireguard connects after I say `wg-quick up $configname`, with `ip a` I can see a new interface with an IP that corresponds to my configuration, there is a route set (Dst 10.9.0.0 -> Iface $configuration_wg0) BUT …

I read a lot of U Boot documentation the last hours but I still fail at fundamental understanding, like: - where can variables be set? boot.scr obviously, but there is also uEnv.txt boot.cmd armbianEnv.txt ... and in which order and precendence are they parsed? (If I set a variable in different files, which value will be used? first? last? ...) - how is a change made persistent (saveenv does not work) - Can sub-variables be changed, e.g. root in bootargs what I am trying to achieve atm is to change the boot partion rootdev from p1 to p2. Even thou I think I patched the relevant files, printenv shows that bootargs and rootdev are still set to…

I am trying to setup my Odroid-XU4 with Armbian 20.05.2 booting from MMC and no SDCard in slot. It took me a while but finally I found what I needed. Next I've installed OpenMediaVault using armbian-config, that worked well. Within OMV I've tried to setup VLANs which I could define but they didn't work, so I had to take a deeper look into it. I've found that the interface name needed to be reverted back to eth0 since the new naming convention enx<MAC-address without ":"> uses the max available number of characters already: In my case "enx001e06320261" , so if you add a vlan "enx001e06320261.1" the name is to long, it will not start. This could be so…

Great job here! I need video acceleration on my bPI+. I found some outdated info and hints but nothing solid, can this be done? Can I find (or build) a legacy kernel somehow? How/where? Thanks again, armbian is amazing!

Hello, I usually don't have a problem with this but today a couple of SHA checksums didn't work for Armbian_20.05.2_Odroidc2_buster_current_5.6.15.img.xz Armbian_20.05.2_Odroidc2_buster_current_5.6.15_minimal.img.xz I redownloaded both a couple of times, same result. Could anyone else confirm? From here: https://www.armbian.com/odroid-c2/#kernels-archive-all

Wondering if anyone has an operating mPCIE Kingston SSD working like this one. This one isn't being recognised.

From https://www.armbian.com/odroid-hc1/ I have downloaded Armbian_20.05.2_Odroidxu4_buster_legacy_4.14.180.img.xz on several different machines and internet connections and done a checksum verification using several different utilities and there is always a mismatch. Armbian_20.05.1_Odroidxu4_buster_legacy_4.14.180.img.xz.sha says the SHA-256 checksum should be DDAF33314FAE4515E047702257CCA93CC0C088D73F81118EA8CE6911E89210EB but the checksum utilities always report E8E31E653798EBC0FFCE9205A6D7BD625EA58F8728339E4D04604A002D737DEE I downloaded Armbian_20.05.2_Odroidxu4_focal_current_5.4.41.img.xz (which doesn't work wi…

Hi, I've bought a pandoo box with an amlogic s912,2 3g of ram and a mali t820, I've found a couple of dtb files (vegas and meson-gxbb-p200.dtb I think) that make it boot but without wifi nor bluetooth, I've tried extracting the one from android using termux and dd /dev/dtb with no luck... is there anything else to try? any way to make wifi and bt work? Any help is appreciated Thanks!

Hi, I need help. I've compiled the kernel, installed it with dpkg, but it keeps booting from the upstream kernel, how to set the env var to force the new kernel??

Hi, I installed more than one year ago pi-hole on a Orange Zero, since two/three month the admin panel of pi-hole remind me that there is a new pi-hole version available. I cannot figure out which is the correct way to upgrade it. Will the upgrade be released as a package through the armbian apt repository? I mean, will I get this upgrade with apt-get upgrade sooner or later? Are there other ways to upgrage it? Thanks.

630/5000Best... I have the latest version of Armbian for the Odroid N2. Running on a 64gb emmc Installed on a home automation system. Nothing else. login as: pi pi@192.168.5.70's password: ___ _ _ _ _ _ ____ / _ \ __| |_ __ ___ (_) __| | | \ | |___ \ | | | |/ _` | '__/ _ \| |/ _` | | \| | __) | | |_| | (_| | | | (_) | | (_| | | |\ |/ __/ \___/ \__,_|_| \___/|_|\__,_| |_| \_|_____| Welcome to Armbian Focal with Linux 5.6.15-meson64 System load: 39.73 47.94 41.55 Up time: 8:34 Memory usage: 96 % of 3634MB Zram usage: 100 % of 1023Mb IP: 192.168.5.70 CPU temp: 35°C Usage of /: …

edited

hello. first i want to say thank you to every armbian supporter and the hole team. thanks for providing this nice project and your work. i did some work for adding an external sound card - the audioinjector pi stereo, which is based on a wm8731. i used the radxa rockpi4(b) board based on the rk3399. i choose this board because of pinout header is nearly the same as the one you find on raspberrys. so adding/ using raspberry Hats won´t be too hart in this case. this will also work with radxa kernel https://github.com/verplant23/kernel so there shouldn´t be any troubles porting it to armbian legacy. i´m not a coder and i don´t kno…

On my Orange Pi Zero I run Armbian Buster and the only software running is Shairport. Unfortunately I used to have a crackling noise every 20-40 secund which was solved after entering root@orangepizero:~# renice -n -19 -u shairport-sync 110 (user ID) old priority 0, new priority -19 So far so good - but after a reboot the prio is again 0. So I tried to use nice nice -19 shairport-sync but after a reboot the prio was again 0 How can I set the priority of all process run by the user (-u) “shairport-sync” to -19 when they start?

OrangePiZero, Armbian_20.05.1_Orangepizero_buster_current_5.4.43 in RPI they have an option "Boot without waiting for network connection" which to be honest I do not know does what under the hood. What can I use with armbian to get faster boot time? I do not use Ethernet at all, I use wifi but do not want to wait for it to start using my device. Here is my boot statistics: root@orangepizero:~# systemd-analyze Startup finished in 7.295s (kernel) + 29.971s (userspace) = 37.266s graphical.target reached after 29.810s in userspace root@orangepizero:~# systemd-analyze blame 8.967s networkd-dispatcher.serv…

Hello, I've copied the Armbian Bionic image onto an SD card (and verified it) and put it into my new Orange Pi Zero LTS 256 MB. I already have experience with Raspberry Pis and Raspbian for a few years, so this isn't entirely new to me. While I was trying to establish a stable network connection (wired and wireless), I misinterpreted some "host not reachable" as "network failed" when instead other issues existed. In the process, I unplugged the power a few times after the device has booted up but wasn't reachable via the network. Only then I connected the serial console and investigated further. There I found out that it wasn't actually booting any…

It been a while since I have made custom images for the OrangePi PC Plus so things have changed a bit in the intervening period. First I made the development environment change to Ubuntu Focal, then changes to a couple of patch files to bring them into line with the new u-boot and kernel versions however I have simply lost the ability to display an Armbian splash screen during boot. In the past I had patched general-armbian-boot-logo-on-screen-center.patch and general-armbian-boot-logo-on-screen-center copy.patch to show the splash screen I required however now these patches are this patch is no longer even referenced during the build process. Now, after th…

I installed gnome-software on armbian Ubuntu 20.05 based on Ubuntu 20.04 LTS, the gnome-software store opens when I try to install any software, the store closes and does not install, can someone help solve this problem, I was only able to install the program when I installed it the snap-store by the chromium browser I downloaded the snap-store armhf version.

I try to update my jessie installation on orange pi one but I get errors. My kernel version is 3.4.113-sun8i My armbian.list file is this deb http://apt.armbian.com jessie main utils jessie-desktop My sources.list file is deb http://httpredir.debian.org/debian jessie main contrib non-free #deb-src http://httpredir.debian.org/debian jessie main contrib non-free deb http://httpredir.debian.org/debian jessie-updates main contrib non-free #deb-src http://httpredir.debian.org/debian jessie-updates main contrib non-free deb http://httpredir.debian.org/debian jessie-backports main contrib non-free #deb-src http://httpredir.debian.org/debian jessie-backport…

Hi I am not very experienced with armbian/linux. I have a raspberry pi that is connected to a 4K tv via HDMI. When I turn the tv off and on screen resolution changes to 4K. I need to fix it to 1080p. I searched but couldn't find something I can understand. How can I do this?

I run this command I saw that my system clock is not synchronized. destructor@orangepiplus:~$ timedatectl Local time: Mon 2020-05-18 14:05:45 EEST Universal time: Mon 2020-05-18 11:05:45 UTC RTC time: Tue 1970-01-06 15:48:55 Time zone: Europe/Kiev (EEST, +0300) System clock synchronized: no NTP service: inactive RTC in local TZ: no So how can I active ntp server? I undestand that is common Linux OS question but when I installed Linux OS on PC devices it never disturb me because there it worked as default

I guess my application is IOT - I am getting data via USB and SPI, report status via GPIO LEDs and upload data to the internet. I am enjoying raspberrypi 3B but it's huge and relatively expensive. I am trying to return Orange Pi 2G IOT since it's a disaster. Looks like Orange Pi Zero for a bit under $20 would not be a disaster? Are there other boards to consider if I care about physical size and price?

Hi all, I have several Nanopi M4V2's running 24/7 which I use for prototyping my projects , I would like a UPS as a safety backup to power them. I'm in the UK has anybody got any suggestions as to what I should consider ? I hope this is the right forum for this post

I can't synchronize the clock using my GPS module. I get this error message: ntpd[1345]: kernel reports TIME_ERROR: 0x41: Clock Unsynchronized It only appears when I use my GPS source. When connecting to NTP servers, everything is okay. http://ix.io/2nUZ I tested it with older kernels, and it works, but I have then other issues. Any help are welcome.

I've tried to compile libgpiod (my assumption is this is a user space lib) and it depends on gpio.h which is used by the kernel. According to https://github.com/brgl/libgpiod/issues/22 gpio.h should be installed with linux-libc-dev which is already installed and gpio.h is missing. I installed the kernel headers and tried (it ends up with typedef conflicts): ./autogen.sh --enable-tools=yes --prefix=/usr/local CFLAGS="-I/usr/src/linux-headers-4.14.14-sunxi/arch/arm/include -I/usr/src/linux-headers-4.14.14-sunxi/include" configure: error: linux/gpio.h header not found (needed to build the library) I've attached the config.log. Maybe I'm to…

<smaeul> scanning bus dwc3@5200000 for devices... 2 USB Device(s) found <smaeul> wooo, got USB3 boot working on H6 :D patchset at https://github.com/smaeul/u-boot/commits/h6-dwc3 Just catched this on #linux-sunxi IRC channel. I do not have a H6 board to test this but maybe someone else wanna give it a shot.

Hi there, I have just do a fresh install of armbian (Armbian_20.02.5_Odroidn2_buster_legacy_4.9.216) on odroid n2 and installed omv 5 via armbian softy tool. Docker was installed via omv gui - omv extras - docker / portainer. When I now try to setup a separate network in docker / bridged mode I get the following error: docker network create --driver=bridge --subnet=192.168.151.0/24 --gateway=192.168.151.1 home Error response from daemon: Failed to program FILTER chain: iptables failed: iptables --wait -I FORWARD -o br-7a5194cdef64 -j DOCKER: iptables v1.8.2 (nf_tables): RULE_INSERT failed (Invalid argument): rule in chain FORWARD (exit status 4) …

Hi, all: Today I just upgraded my packages as normal, by using "apt update && apt upgrade", on my RockPi 4B (legacy kernel), and I saw there was a hostapd package updated. However, after this upgrade, my hostapd won't start anymore now: Configuration file: /etc/hostapd.conf wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE Using interface wlan0 with hwaddr 6c:21:a2:37:ff:1a and ssid "RockPi-Armbian" Failed to set beacon parameters Interface initialization failed wlan0: interface state COUNTRY_UPDATE->DISABLED wlan0: AP-DISABLED wlan0: Unable to setup interface. wlan0: interface state DISABLED->DISABLED wlan0: AP-DISABLED wlan0: CTRL-EVENT-T…

So I downloaded Armbian_20.02.1_Orangepione_buster_current_5.4.20_desktop and I boot it up in my Orange PI PC and it started very well, there is one issue, I noticed that just one USB port is working, so I can only work with a mouse or a keyboard (It sounds dumb I know), so do you have any solution for that? Also I would like to know if a wifi dongle can work with this image.

I want to use orange pi pc plus for kiosk. Is there any way to disaplay own logo or any image during boot process instead for kernel messages. I have managed to disable kernel messages during boot up process but not it black screen. What changes should I make to display own logo or image during boot process insead of kernel messages.

Hello, I have an Odroid C1+ . I tried to use it with the recommended Armbian Buster. Unfortunately the SSH connection is very slow, when I type in a command I get a very delayed response that makes it very difficult to use. Any idea ? Thank you

I'm trying to setup Ethernet connection on Omnima A20 - it's a cheaper stripped down version of Cubietruck (less RAM, less IO connectors, RTL8201CP 100Mbit network chip instead of 1Gbit). I'm using Debian Buster server image for Cubietruck. Everything works fine except Ethernet. ethtool says the link is up, full duplex 100Mbit. Neither networkmanager nor dhclient are able to obtain IP address from router. Static IP assignment (via /etc/network/interfaces or with "ip addr add/ip route add") succeeds, but router is unreachable for ping ("Destination Host Unreachable"). I've ruled out hardware failure: Inserting the same cable into laptop produc…

Hi all, I use a cubieboard3 as a web server. For several months, joomla tells me that I am PHP 7.0.33-0 + deb9u7et that I need to update my version of php to 7.3 or later. In the updates of the bone, I never see these updates of PHP, must it be done manually and how? I am in Debian Stretch with Armbian Linux 4.19.62-sunxi. Thank you François

Strange problem with armbian-config/softy/OMV But something similar has happened to me also with a simple update from armbian-config Steps to reproduce: 1. clean install of Armbian_20.02.1_Orangepi3_buster_current_5.4.20 using uart-ttl usb adapter as interface 2. I configure the network by wifi 3. apt update && apt upgrade -y 4. after the terminal update everything is still perfect and I can connect to ssh with WIFI and launch armbian-config 5. armbian-config/software/softy/OMV -> Install Results: After a coffee or two, I go back and find that the ssh connection has been closed and I can't connect. Notes: Enteri…

Hello. I feel like this is a really basic stupid question, but for the life of me I can't find an answer. Every thread that I read about getting a display XYZ to work in Armbian references using fbtft. But apparently fbtft is now deprecated and cannot be used anymore. So.. what do I do now? I'm mainly looking to get ILI9341 -based 3.2" TFT and MPI3508 3.5" TFT to work with Armbian. Mainly testing with an Orange Pi Lite2 and Orange Pi 3 currently. I've read this: downloaded, compiled and installed the .dts. Also modified/added line to boot.cmd to use lcd as display according to https://docs.armbian.com/Hardware_Allwinner/ tha…

Hi I'm trying to use OpiZero with a relais module. I noticed, during the boot the pins I tried (12 and 11, physical 3 resp 5) go high, which makes impossible to manage the relais module. Is it a HW/SW bug or limitation or something what can be configured somehow. I would expect the level to be "nothing" ;-) Thanks Chris

Hello, this may be related to: https://forum.armbian.com/topic/8819-where-to-report-a-bug-etcinitdarmhwinfo-corrupts-bootarmbianenvtxt-when-followed-by-powerfailure/ https://github.com/armbian/config/issues/33 cat /boot/armbianEnv.txt /var/log.hdd/alternatives.log { monthly rotate 12 compress delaycompress missingok notifempty create 644 root root }usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u Would there be any advice so that we can prevent this from happening? Many thanks for any pointer. Regards Rostislav

My Orange Pi PC is restarting without apparent reason at random times and wifi and buses are disabled. The last lines of log always say the same: [ 25.644949] IPv6: ADDRCONF(NETDEV_CHANGE): wlxf4f26d1c6002: link becomes ready [ 33.781109] vcc3v0: disabling [ 33.781136] vcc5v0: disabling [ 33.781146] usb0-vbus: disabling armbianmonitor link: http://ix.io/2mTA Thanks in advanced

Hi, I asked earlier about getting armbian running on a particular RK3399 system-on-module, but I wanted to try a different angle now: is there an RK3399 SoM that currently runs armbian well? For example, this one claims to: http://wiki.friendlyarm.com/wiki/index.php/SOM-RK3399v2 . Has anybody here actually used that board with armbian? I'm more inclined to believe you guys than the people selling the board... George

https://libre.computer/ They appear to be comparable to orange pi computers.They do provide up to 2gb ram and support emmc. Do you have comments about the computers or testet one of them? Thank you.

I can not raise the Access Point. Already my head is spinning on the number of tried recipes from the Internet. Service information here. Help me please. Configuration files: /etc/hostapd.conf ssid=BananaPI-WiFi interface=wlan0 hw_mode=g channel=5 bridge=br0 driver=nl80211 logger_syslog=1 logger_syslog_level=2 wmm_enabled=1 wpa=2 preamble=1 wpa_psk=c86e997b3dceff9bd7ffaf3f7353099a301c2**********d10a892c33cafcb5db wpa_passphrase=10********IV wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP auth_algs=1 macaddr_acl=1 noscan=0 ### IEEE 802.11n #ieee80211n=1 #ht_capab= #country_code=US #ieee80211d=1 ### IEEE 802.11n ### IEEE 802.11a #hw_mode=a ### IEEE 802…

Hi Armbian forum team, i have bought some HC1/XU4, very fine boards, thank's, but have a wifi AP+STA pb. odroidhc1 / kernel: armbian 4.14 / wifi module 3 lsusb -> Bus 001 Device 002: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN Adapter ). lsmod -> rtl_usb 20480 1 rtl8192cu After rebuild hostapd-rtl/driver (to suport nl80211)/AP + wpa_supplicant/STA runs fine but not simultaneously (when wpa_supp connects in STA (AP shutdown, etc..)). In fact that seems normal because in iw "combination is not supported" What 's the best chipset you advise me (rtl8812, rtl8814, rt3572/5572, mt7601, atheros, cypress) which supports AP+STA at SAME TIM…

Hello All, I installed Sonarr and found it had trouble reading from my nfs mounts, only seeing one folder, which turned out to be mono's issue. I used a snapshot of version 5.20 from the raspbian repo apt install apt-transport-https dirmngr gnupg ca-certificates apt-key adv --keyserver hkp://keyserver.ubuntu.com:80 --recv-keys 3FA7E0328081BFF6A14DA29AA6A19B38D3D831EF echo "deb https://download.mono-project.com/repo/debian stable-raspbianstretch/snapshots/5.20 main" | sudo tee /etc/apt/sources.list.d/mono-official-stable.list This is working fairly well for me so far and I will post back if I run into problems. Using 5.20 to avoid some of the regression and t…

Hi All, I'm planning to use an RK3399-based system-on-module for an embedded application, and would like some advice about the work required to produce an Armbian build that runs on it. The SoM is made by Graperain ( https://www.graperain.com/ARM-Embedded-RK3399-System-On-Module-Gf/ ), and they have provided an SDK which is clearly an old copy of the Rockchip's github repo (4.4 kernel) with some unidentified tweaks to get it working on this board (including .dts files and presumably some bootloader stuff?). I realize this particular board is likely not of interest to the community, but I figure the general discussion around getting a new board running may be. …

see title, can help setup letsencrypt cron if needed

--- armbian-hardware-optimization.orig 2020-05-17 10:53:46.352578716 +0200 +++ armbian-hardware-optimization 2020-05-17 10:54:02.052970679 +0200 @@ -67,7 +67,7 @@ [[ -f $prefix/cpuinfo_cur_freq ]] && chmod +r $prefix/cpuinfo_cur_freq 2> /dev/null # enable compression where not exists - find /etc/logrotate.d/. -type f | xargs grep -H -c 'compress' | grep 0$ | cut -d':' -f1 | xargs -L1 sed -i '/{/ a compress' + find /etc/logrotate.d/. -type f | xargs grep -H -c 'compress' | grep 0$ | cut -d':' -f1 | xargs -L1 sed -i '/{/ a compress' 2> /dev/null sed -i "s/#compress/compress/" /etc/logrotate.conf …

See https://wiki.debian.org/DebianGeoMirror On my install apt-get update yielded device or resource busy, fixed it by changing apt repository to http://deb.debian.org. weird, now it works alright

Just wondering if anyone has Webmin running on their Arm system. I have encountered problems installing and using a dependency "apt-show-versions" I have studied and attempted to resolve the issue using information on this page https://serverfault.com/questions/845192/dependency-problems-while-installing-webmin It goes into a fair bit of detail, but unfortunately nothing is working. Can anyone put me on the right track?

Dear Armbian expert, The Armbianmonitor sumbit generate URL with the following error. System diagnosis information will now be uploaded to /usr/bin/armbianmonitor: line 859: [: -gt: unary operator expected

I am trying to investigate why borg backups, specifically when doing borg check, are taking over twice as long on armbian buster + OMV5, compared to armbian stretch + OMV4. The borg server is an Odroid HC2, and borg check runs on the server (HC2) and is single threaded. Not sure where to even start, but one thing that caught my attention is that the borg process will be running at 100% CPU at various times (as expected), but the CPU frequency at those same times was reported at 200-300 MHz when observed using htop. Is this normal? Unfortunately I don't know what frequency was normal in the same circumstances with armbian stretch + OMV4. Benchmarks …

good morning . can you explain something? . is it possible to use voice control to transmit audio wirelessly to the speakers with nanopi + NanoHat PCM5102A as happens with google assistant + chromecast audio?

Hello, I will use the integrated CAN-Controller with the actual version of Armbian Bionic (or Buster) on the BananaPi-M1 Actually it is not possible to activate the CAN-Bus. I had activate the CAN in the armbian-config. After a reboot I the CAN0 is not integrate in the list from "ifconfig -a". What are the steps to activate the CAN-Bus on the BananaPi M1. Many thanks, André

Hi: I am new to Armbian Buster. I understand the legacy h3consumption is gone now. I wonder if I can do something similar under Armbian Buster like: 1. only allow 1 or 2 core 2. lower ram frequency 3. disable hdmi

Hello. I'm trying to install Jeedom on my Odroid C2 running Linux odroidc2 5.4.14-meson64 (Armbian_20.02.0-rc1) Distro has been updated with : apt-get update apt-get upgrade But when I download and run the install script : wget https://raw.githubusercontent.com/jeedom/core/stable/install/install.sh chmod +x install.sh sudo ./install.sh I have an error : Reading package lists... Done Building dependency tree Reading state information... Done Package mysql-client is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source Package my…

hello, i need help porting Goodix gt911 touch panel into orange pi plus 2E (h3), the reset pin is at PA1 and interrupt pin is at PA0 here is my dts. soc@01c00000 { twi0: twi@0x01c2ac00{ gt911@5d { compatible = "goodix,gt911"; reg = <0x5d>; interrupt-parent = <&pio>; interrupts = <0 IRQ_TYPE_EDGE_FALLING>; /* EINT0 (PA0) */ irq-gpios = <&pio 0 0>; /* INT (PA0) */ reset-gpios = <&pio 0 1>; /* RST (PA1) */ irq-flags = <2>; touchscreen-max-id = <11>; touchscreen-size-x = <1280>; touchscreen-size-y = <720>; touchscreen-max-w = <512>; …

Hi folks, I'm running armbian on a Banana Pi 1st generation, so far no probs. Indeed it runs very stable. The armbian is a debian jessie. Is it possible or recommended to update to stretch via the official debian upgrade path ? The armbian is fully updated Welcome to ARMBIAN 5.36 user-built Debian GNU/Linux 8 (jessie) 4.13.16-sunxi I'm running an nginx php stack on the BaPi. But what about stretch ? Can I do a dist-upgrade ? Sorry if this has already been discussed. Thanks in advance for replies :-)

i have a clearfog pro with ARMBIAN 5.49 Need to set static LAN interface IP address with gateway, and WAN interface is also static IP address, Please let me know is it possible to set two gateway in Clearfog pro for WAN & LAN,

I have installed syslog-ng which removes rsyslog, now I am trying to filter using journald as docker is set to log to journald. If I create docker.conf in /etc/syslog-ng/conf.d with: filter f_dockerd {"${.journald._COMM}" eq "dockerd"}; destination d_docker { file("/var/log/docker.log"); }; log { source(s_src); filter(f_dockerd); destination(d_docker); }; Everything is logged go to docker.log, not just docker logs. The journal source is already setup with system() I think as if I try to add a journald source I get the error there can only be one.

Hi Everyone, I have a clean install of armbian with vanilla gnome installed, it boots to the login screen and mouse seems fine but after a few seconds it stops responding and when you move it it does this weird rapid shake movement as if your moving the mouse like 2 pixels side to side 100 times a second, its hard to explain but the curser doesn't move. Every reboot and the same thing happens and I tried starting from scratch with a fresh flash but same results happen and also tried different mouse, they work fine on other machines though. Has anyone come across anything like this before who can possibly offer some advice? Sorry if I haven't explai…

Hi: I am using debian jessie on orange pi H3 boards and I am very satisfied with it. but I need to upgrade now since jessie is out of support. i want to upgrade to debian buster since my pi is using as a server without any display attached. but I wonder maybe there is something good I missed from ubuntu: like 10 years LTS support? or perhaps most developers are using ubuntu so it is more mature? just need some advice. thanks a lot!

before you start: Armbian already provides kernel build script in armbian build framework, and you can download these packages via `apt` in common cases, you shouldn't build kernel yourself, even you want to build a customer kernel package, you should use armbian build framework. because you can get best supports. so below content is only for experts. prepare source code: 1, stable linux kernel source code: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git https://kernel.googlesource.com/pub/scm/linux/kernel/git/torvalds/linux.git 2, armbian build framework, fo…

Hi all, I am using Armbian Bionic on ASUS Tinkerboard S board(s) in an application where the power may fail at any point. I have now, for the second time, seen a running OS starting to fail with the error. ALERT! /dev/mmcblk0p1 does not exists. Dropping to a shell! I have restarted the board several times, but the error continues. If I do a: (initramfs) blkid /dev/mmcblk2p1: UUID=.... /dev/mmcblk2: PTUUID=.. It seems that the OS tries to boot from the wrong device. If I then, booting from another OS using SD card, change the /boot/boot.cmd rootdev: setenv rootdev "/dev/mmcblk2p1" And rerun the mk…

Using my Orange Pi Zero 512 H2 I want wo build a POE-powered display, displaying the current time, time until the bus leaves and ideally some information on bus schedules I can pull from the API of the local bus network. What I currently have is an Orange Pi Zero 512 H2 and a POE injector where I can insert any voltage as it does not run with standard POE voltage. My plan is to buy this e-paper display https://www.waveshare.com/wiki/7.5inch_e-Paper_HAT_(B) and have the Orange Pi display a simple HTML page. So my first question is: Would this display run, would it be a good choice for my setup? Are there any similar projects (yes, I searched) that…

Ubuntu changed the location of the mini.iso file for the minimal Ubuntu (Server?) installer in their file servers (since the 20.04 release), it's now located here: http://archive.ubuntu.com/ubuntu/dists/focal/main/installer-amd64/current/legacy-images/netboot/mini.iso The docs should be changed since it could be confusing for new users/developers.

Alan in Sydney, Australia. I've loaded: eoan desktop, Linux aml 5.5.0-rc6-aml-s9xxx #rc1.038 SMP PREEMPT Thu Feb 6 10:21:51 MSK 2020 from the 20200205.zip file and upgraded. root# mkdir -p /sys/kernel/config/device-tree/overlays/i2c3a cannot create directory ‘/sys/kernel/config/device-tree’: Operation not permitted What am I trying to do? On an Odroid N2 compile with GCC 10 (from Fedora) "neural networks" code (FreeDV) using the ARMv8 SVE extensions. (Odroid N2 is not supported on Fedora)

Hello everyone. I'm trying to configure wifi on my orange pi zero based on armbian buster. I planed to work in two wifi modes - client mode and access point mode. Wpa_supplicant allows me to register several networks in one configuration file, one of the networks can be with the option mode = 2, which means an access point. Then if during scanning wpa_supplicant does not find available points for connection, its own access point is created (which with mode=2 in conf file). I have problems with connecting other clients to this access point (it sees, but always reconnect). dnsmasq works as dhcp server as service, but i try to connecnt with static Ip on client too - no resul…

Hi guys, I am going to apply some LibeELEC multimedia patches to Armbian kernel Please advise, what is the proper way for this? I have found folder build/userpatches/kernel/sunxi-current. Should I put files here?

Hi, Is nand-sata-install script still included in Armbian_4.5_Cubox-i_Debian_jessie_3.14.54.raw ? Thanks

Hello, Trying to compile the Qualcomm Gobi serial USB drivers for a Simcom wireless chip on a NanoPi Neo2 (sunxi64). I've loaded the kernel headers via armbian-config and typically this specific header file would be in drivers/usb/serial. We're using the pre-built image. Is there an easy way to get this into our kernel or do we have to embark on a full compile? Any help very much appreciated Rob

I just got a working version of the mcp251x.dts overlay running an the Allwinner H3, and ran into a few issues along the way. I'd like to save someone the pain and maybe find the right place for a bug report for the old version of dtc in the image. Compiling the overlay with armbian-add-overlay fails on the target system because the following throws: dtc -@ -I dts -O dtb -o mcp251x.dtbo mcp251x.dts ... dtc: livetree.c:521: get_node_by_phandle: Assertion `(phandle != 0) && (phandle != -1)' failed. aborted The best reference I can find for this symptom is: https://patchwork.kernel.org/patch/10015389/ Following them, commenti…

hello, and sorry for my English I installed Armbian and i have many problem : 1/ I want a auto-login at startup, but I don't know how to do. 2/ I want stay the command line , and choose to startup on desktop. 3/ I have a problem to return to command line then i am on desktop (with default desktop). 4/ that other desktop works on Armbian and how to install them cordially Rachel

Actually this is answer not a question . How to drive things with the OrangePi board with smartphone? My GOAL was : 1. create Access Point with Orange Pi Lite board. 2. create wireless local network with Nodejs 3. connect my smartphone to this wireless network So , I think almost all kind of boards could work , from Raspberry pi , Orange pi and many others boards families with wireless adapter . This is tested on OrangePiLite board with OS-Armbian 5.65 with node.js installed. First you have to create two files - server.js and index.html(see below) server.js is your nodejs server script file who will handle index…

Hi, I have an Orange Pi Zero configured as a Wireless Access Point (via armbian-config) and it works great. However, I want to be able to scan for wireless networks whilst configured as an AP. If I try scan, I get the following error: wlan0 Interface doesn't support scanning : Operation not supported Just wondering if this is a shortcoming of the driver or the XR819?

Hello, I will use the BPI M3 with armbian and a GPU support. With my understandig GPU is with the normal installation not activated. What is the way to actvate this? Many thanks for the support, André

Hi all, this is somewhat odd. I am using the nextcloudpi image NextCloudPi_Rock64_03-28-20.img. I believe it uses armbian (I am really not an expert sorry) and my problem is really not nextcloud related i believe. I had to cut the power to the rock64. Then i rebooted. The system clock is set to some early date (2016-xx-yy). Therefore the unmount is in the future causing an fsck. It fails miserably and drops to initramfs (where i really am lost). I don't think this should happen. I dont have a rtc battery - maybe this wouldnt be an issue if there was one attached? I hope someone can tell me how to progress or how to provide better insight …

Hi, Could anyone please help me to configure CB3 and the subboard RAID? In fact, I own a CB3 and the RAID subboard with two SSD 120GB that I bought at Cubietech three years ago and I have already assembled it. I use the Armbian distribution for Cubietruck and I installed it on a SD Card, but now I would like to install this distribution (Armbian for CB3) on the two SSD from the SD card. If I type the following commands 'hwinfo --block' or 'fdisk -l' or 'lsusb' or 'lsblk -o name' at the prompt (as root), I do not see any SSD except the SD Card (mmcblk0) I also launched 'armbian-config' but nothing appear in the menu about that. I have done some onl…

I use Armbian Buster on ODROID-C2. I try to install the package "syslinux" with apt, but it's not there. What now? apt install syslinux Reading package lists... Done Building dependency tree Reading state information... Done Package syslinux is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package 'syslinux' has no installation candidate

On my OrangePi+2e MAME run to slow in Full screen mode!!!! When i resize window in a small resolution , everything runs ok...but when i m larging the screen , then i have a speed problems with MAME games. Is there anyone else with the same issue???

I installed armbian_eoan_desktop_5.5 on my set-top box and updated mesa to 20.1-devl . But I found out the Xfce4 desktop is a little bit larger than my TV screen . I checked the Application->setting->display and used xrandr -q to print out the parameters : Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 3840 x 2160 HDMI-1 connected primary 1920x1080+0+0 (normal left inverted right x axis y axis) 575mm x 323mm 1920x1080 60.00*+ 60.00 50.00 59.94 24.00 23.98 1920x1080i 60.00 50.00 59.94 1680x1050 59.88 1280x1024 60.02 1280x960 60.00 1360x768 60.02 1280x800 …

I'm using an Orange Pi Prime to build a Magic Mirror. The module I'm trying to install is for switching the HDMI on/off with a PIR sensor. The module is called MMM-PIR-Sensor. The readme file it says to execute this command sudo chmod u+s /opt/vc/bin/tvservice && sudo chmod u+s /bin/chvt. The result I get is:chmod: cannot access '/opt/vc/bin/tvservice': No such file or directory. I believe the module is set up for Raspberry pi and the issue I'm having is due to disconnected libraries? Anyways, I'm relatively a novice so any help to figure this thing out is greatly appreciated. The OS I'm using is Armbian 20.02.1. Let me know if there is any other info need…

Time to time i got following notification on Banana Pi M1. Only after reboot Banana starts working properly. How to tune zram to avoid such kind of issue? No tuning made till now Linux bananapi 4.19.17-sunxi #5.73 SMP Mon Jan 28 21:06:40 CET 2019 armv7l GNU/Linux error: Compressing program wrote following message to stderr when compressing log /var/log/letsencrypt/letsencrypt.log.1: gzip: stdout: No space left on device error: failed to compress log /var/log/letsencrypt/letsencrypt.log.1 error: Compressing program wrote following message to stderr when compressing log /var/log/wtmp.1: gzip: stdout: No space…

Xupdate: includes updated mesa libraries for mali GPUs. how to use: add below to you source.list gpg key can be found at: after that, run `sudo apt update && sudo apt upgrade` before reboot, please update your xorg.conf, follow below webpage:

I installed Armbian Bionic Desktop 4.4 on the emmc module and I also have an SD card in. When I get to the desktop the card looks like it has been mounted by the current user (I'm new to Linux) - it was listed under /media/myuser with myuser as user and group -, so I changed /etc/fstab to have it mounted during system boot, by adding: /dev/mmcblk0p1 /mnt/sdcard This is what lsblk says: mmcblk1 179:0 0 14.7G 0 disk └─mmcblk1p1 179:1 0 14.5G 0 part / mmcblk1boot0 179:16 0 4M 1 disk mmcblk1boot1 179:32 0 4M 1 disk mmcblk1rpmb 179:48 0 4M 0 disk mmcblk0 …

I have an orange pi lite, I want to use the lcd ili9341 3.2 model SKU: MSP3218 touch screen, and how the installation connections I don't know are these jumpers wires in the gpios correct and if possible use the sd card reader in the orange pi uart? I need your help. I be very grateful. The OS is "Armbian_20.02.0-rc1_Orangepilite_buster_current_5.4.14_desktop"

Hi. I'm trying to use microusb port as additional usb port on OrangePi Lite. uname -a Linux orangepilite 5.4.31-sunxi #20.02.11 SMP Thu Apr 9 21:47:57 CEST 2020 armv7l armv7l armv7l GNU/Linux I've tried enabling usbhost0 in armbian-config and modify sun8i-h3-orangepi-lite.dtb as described here: In both cases I have no power on microusb port. What am I missing? Thanks Christian

A fatal error has been detected by the Java Runtime Environment: # # SIGILL (0x4) at pc=0xb40aba7c, pid=320, tid=327 # # JRE version: OpenJDK Runtime Environment (11.0.4+11) (build 11.0.4+11-post-Ubuntu-1ubuntu218.04.3) # Java VM: OpenJDK Server VM (11.0.4+11-post-Ubuntu-1ubuntu218.04.3, mixed mode, serial gc, linux-) # Problematic frame: # J 28 c2 java.lang.StringUTF16.toLowerCase(Ljava/lang/String;[BLjava/util/Locale;)Ljava/lang/String; java.base@11.0.4 (296 bytes) @ 0xb40aba7c [0xb40ab880+0x000001fc] # # No core dump will be written. Core dumps have been disabled. To enable core dumping, try "ulimit -c unlimited" before starting Java again # # An…

Hi, I'm running the latest bionic image (nightly build) on my rock64pro. (I've tried with the stable build but it has the same result) uname -a Linux 4.4.166-rockchip64 #22 SMP Fri Dec 14 00:56:53 CET 2018 aarch64 aarch64 aarch64 GNU/Linux I've used armbian-config mayan edms 3rd party software installation option but it failed during the mayanedms/mayanedms container deploymentment. With docker events& turned on I saw the next message: standard_init_linux.go:190: exec user process caused "exec format error" I found a recorded issue in mayan edms gitlab and it looks this issue is still not resolved: https://gitlab.com/mayan-edms/may…

Hello everyone I have a problem with icecast because I can't get the let's encrypt ssl certificate to work. I have followed several tutorials online, but in the end they were all the same, so I explain what I am doing, to see if someone tells me where I am wrong. I have created a script to concatenate certificates, change ownership and permissions, so that I can run it with cron along with the let's encrypt certbot. Here the script ---------------------- #!/bin/bash cat /etc/letsencrypt/live/radio.example.org/cert.pem \ /etc/letsencrypt/live/radio.example.org/privkey.pem \ > /usr/share/icecast2/icecast.pem chown icecast2.icecast /usr/s…

Hi, I have Armbian-Buster installed on my ODROID-HC2. And everything is working perfectly. But today I opened armbian-config and installed Pi-Hole, installed OK. Checked to install Radarr. Installed OK Checked to install Sonarr. Said it is not installed, the check is not marked, but it was installed and I can even see the /etc/systemd/system/sonarr.service file. OK. I want to REMOVE all three. When I open armbian-config and select the pi-hole or Radarr, the interface just blinks and return to the list, Nothing is uninstalled. Where's the log file so I can see what may be the problem ? …

Hi all, I bought a Orange Pi PC 2 a couple of months back, loaded the Armbian image successfully and tweaked it until it was just right for my application. As this piece of hardware was going to live on a remote property, I bought another 2 Orange Pi PC 2 boards and some new SD cards with the intention of having 2 backups - one for development and the other as spare. I cloned the SD card by copying the active EXT4 partition across to the blank SD card using GParted. The long and the short of it is that these images did not work. I know the hardware is good as the original SD card works in the new OPi PC2 boards. Likewise the new cards don't wo…

I try to use the pwm from GPIO to PWM control a fan. I would need around 20kHz with a variable duty cycle. As far as I understand I need to activate the pwm overlay, but its only available for the h5. Can I change the UART or I2C overlay to achieve this or should I try to write my own overlay? Is that even doable?

I posted here since this is more a generic question related to initrd than specific to board My scenario is this: I modified my ARMBIAN uInitrd ( unpacked and repacked ) and added a driver I needed , in particular driver for recognizing internal nand. Of course in the init script I added insmod aml_nftl_dev.ko The process was successfull and infact now i can see the internal nand lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT mmcblk0 179:0 0 980M 0 disk |-mmcblk0p1 179:1 0 128M 0 part /boot `-mmcblk0p2 179:2 0 848M 0 part / cache 250:0 0 512M 0 disk logo 250:1 0 32M 0 disk recovery 250:2 0 3…

Hi. Can someone please kindly shed a light on Armbian / Debian / Sunxi release information that is confusing me: I run Armbian Buster on two Cubietruck systems - one was freshly installed, the other upgraded from a previous installation. Both systems were apt-updated/apt-upgraded most recently with identical /etc/apt/sources.list, and subsequently rebooted. Both systems report identical "uname -a" (=Linux ... 5.4.30-sunxi #20.02.9 SMP) and /etc/debian_version (=10.3) information. The /boot folders have identical zImage resp. uInitrd links pointing to identical targets. Still the /etc/armbian-release resp. /etc/armbian-image-release infos differ: …

My problem system crash when physical memory(actualy mem chache) is full. I think when mem cache is full system try to use swap.Then kernel crash. I fix this problem with crontab job * * * * * sync; echo 1 > /proc/sys/vm/drop_caches Cleary every minute cache memory System keep running look like every things fine.But this is a very bad solution. How can i solve this issiuse? System detail -My hardware T9 tv box Forum https://forum.armbian.com/topic/8082-armbian-for-tv-box-rk3328/ System image Armbian_5.96_Rk3328-tv_Debian_buster_defaul…